參數資料
型號： XRT75L00D
廠商： Exar Corporation
英文描述： E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述： E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER
文件頁數： 33/92頁
文件大小： 894K
代理商： XRT75L00D
XRT75L00D
REV. 1.0.2
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
28
The Equalizer can either be “IN” or “OUT” by setting the REQEN pin “High” or “Low” (in Hardware Mode) or
setting the REQEN control bit to “1” or “0” (in Host Mode).
R
ECOMMENDATIONS
FOR
E
QUALIZER
S
ETTINGS
:
The Equalizer has two gain settings to provide optimum equalization. In the case of normally shaped DS3/
STS-1 pulses (pulses that meet the template requirements) that has been driven through 0 to 900 feet of cable,
the Equalizer can be left “IN” by setting the REQEN pin to “High” (in Hardware Mode) or setting the REQEN
control bit to “1” (in Host Mode).
However, for square-shaped pulses such as E3 or for DS3/STS-1 high pulses (that does not meet the pulse
template requirements), it is recommended that the Equalizer be left “OUT” for cable length less than 300 feet
by setting the REQEN pin “Low” (in Hardware Mode) or by setting the REQEN control bit to “0” (in Host
Mode).This would help to prevent over-equalization of the signal and thus optimize the performance in terms of
better jitter transfer characteristics.
N
OTE
:
The results of extensive testing indicates that even when the Equalizer was left “IN” (REQEN = “HIGH”),
regardless of the cable length, the integrity of the E3 signal was restored properly over 0 to 12 dB cable
loss at Industrial Temperature.
The Equalizer also contain an additional 20 dB gain stage to provide the line monitoring capability of the
resistively attenuated signals which may have 20dB flat loss. This capability can be turned on by writing a “1” to
the RxMON bits in the control register or by setting the RxMON pin (pin 27) “High”.
5.1.1
Interference Tolerance:
For E3 mode, ITU-T G.703 Recommendation specifies that the receiver be able to recover error-free clock and
data in the presence of a sinusoidal interfering tone signal. For DS3 and STS-1 modes, the same
recommendation is being used. Figure 17 shows the configuration to test the interference margin for DS3/
STS1. Figure 18 shows the set up for E3.
F
IGURE
17. I
NTERFERENCE
M
ARGIN
T
EST
S
ET
UP
FOR
DS3/STS-1
SINE WAVE
GENERATOR
PATTERN
GENERATOR
2
23
- 1 PRBS
Μ
ATTENUATOR
DS3 = 22.368 MHz
STS-1 = 25.92 MHz
S
N
Cable Simulator
DUT
XRT75L00D
Test Equipment
相關PDF資料
PDF描述
XRT75L00DIV E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L02 TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75L02IV TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER
XRT75L03D THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
XRT75L04D FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
相關代理商/技術參數
參數描述
XRT75L00DES 功能描述:時鐘合成器/抖動清除器 LIU+DESYNCH 3.3V LIU+DESYNCH 3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L00DIV 功能描述:外圍驅動器與原件 - PCI 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L00DIV-F 功能描述:外圍驅動器與原件 - PCI 1-Ch DS3, E3, SONET RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75L00DIVTR 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75L00DIVTR-F 功能描述:時鐘合成器/抖動清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*