- 您現在的位置：買賣IC網 > PDF目錄376462 > XRT75L03D (Exar Corporation) THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER PDF資料下載
參數資料
| 型號： | XRT75L03D |
| 廠商： | Exar Corporation |
| 英文描述： | THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| 中文描述： | Three頻道E3/DS3/STS-1線路接口單元與SONET DESYNCHRONIZER |
| 文件頁數： | 50/134頁 |
| 文件大小： | 659K |
| 代理商： | XRT75L03D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁
XRT75L03D
REV. 1.0.0
á
THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
45
signal to reduce Inter-Symbol Interference (ISI) so that the slicer slices the signal at 50% of peak voltage to
generate Positive and Negative data.
The Equalizer can either be “IN” or “OUT” by setting the REQEN_n pin “High” or “Low” (in Hardware Mode) or
setting the REQEN_n control bit to “1” or “0” (in Host Mode).
R
ECOMMENDATIONS
FOR
E
QUALIZER
S
ETTINGS
:
The Equalizer has two gain settings to provide optimum equalization. In the case of normally shaped DS3/
STS-1 pulses (pulses that meet the template requirements) that has been driven through 0 to 900 feet of cable,
the Equalizer can be left “IN” by setting the REQEN_n pin to “High” (in Hardware Mode) or setting the
REQEN_n control bit to “1” (in Host Mode).
However, for square-shaped pulses such as E3 or for DS3/STS-1 high pulses (that does not meet the pulse
template requirements), it is recommended that the Equalizer be left “OUT” for cable length less than 300 feet
by setting the REQEN_n pin “Low” (in Hardware Mode) or by setting the REQEN_n control bit to “0” (in Host
Mode).This would help to prevent over-equalization of the signal and thus optimize the performance in terms of
better jitter transfer characteristics.
N
OTE
: The results of extensive testing indicates that even when the Equalizer was left “IN” (REQEN_n = “HIGH”),
regardless of the cable length, the integrity of the E3 signal was restored properly over 0 to 12 dB cable
loss at Industrial Temperature.
The Equalizer also contain an additional 20 dB gain stage to provide the line monitoring capability of the
resistively attenuated signals which may have 20dB flat loss. This capability can be turned on by writing a “1” to
the RxMON_n bits in the control register or by setting the RxMON pin (pin 69) “High”.
5.1.1
Interference Tolerance:
For E3 mode, ITU-T G.703 Recommendation specifies that the receiver be able to recover error-free clock and
data in the presence of a sinusoidal interfering tone signal. For DS3 and STS-1 modes, the same
recommendation is being used. Figure 17 shows the configuration to test the interference margin for DS3/
STS1. Figure 18 shows the set up for E3.
F
IGURE
17. I
NTERFERENCE
M
ARGIN
T
EST
S
ET
UP
FOR
DS3/STS-1
∑
Test Equipment
Pattern Generator
2
23
-1 PRBS
Sine Wave
Generator
N
S
0 to 900 feet
Coaxial Cable
DUT
XRT75L03D
Attenuator
DS3 = 22.368 MHz
STS-1 = 25.92 MHz
相關PDF資料 |
PDF描述 |
|---|---|
| XRT75L04D | FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75L04DIV | FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| XRT75L04 | FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER |
| XRT75L04IV | FOUR CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER |
| XRT75L06D | SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT75L03DES | 功能描述:時鐘合成器/抖動清除器 3 CH T3/E3/STS1 LIU+DESYNCH3.3V RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L03DIV | 功能描述:外圍驅動器與原件 - PCI 3CHNNEL E3/DS3/STS 1 SONET DE-SYNCH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT75L03DIV-F | 功能描述:外圍驅動器與原件 - PCI 3-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT75L03DIVTR | 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75L03DIVTR-F | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。