- 您現在的位置：買賣IC網 > PDF目錄2121 > XRT83SL38IB-F (Exar Corporation)IC LIU SH T1/E1/J1 OCTAL 225BGA PDF資料下載
參數資料
| 型號： | XRT83SL38IB-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 20/88頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| 標準包裝： | 84 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 8/8 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 225-BGA |
| 供應商設備封裝： | 225-BGA（19x19） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
XRT83SL38
25
REV. 1.0.2
OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
RECEIVE MONITOR MODE
In applications where Monitor mode is desired, the equalizer can be configured in a gain mode which handles
input signals attenuated resistively up to 29dB, along with 0 to 6dB cable attenuation for both T1 and E1
applications, refer to Table 5 for details. This feature is available in both Hardware and Host modes.
RECEIVER LOSS OF SIGNAL (RLOS)
For compatibility with ITU G.775 requirements, the RLOS monitoring function is implemented using both
analog and digital detection schemes. If the analog RLOS condition occurs, a digital detector is activated to
count for 32 consecutive zeros in E1 (4096 bits in Extended Los mode, EXLOS = “1”) or 175 consecutive zeros
in T1 before RLOS is asserted. RLOS is cleared when the input signal rises +3dB (built in hysteresis) above
the point at which it was declared and meets 12.5% ones density of 4 ones in a 32 bit window, with no more
than 16 consecutive zeros for E1. In T1 mode, RLOS is cleared when the input signal rises +3dB (built in
hysteresis) above the point at which it was declared and contains 16 ones in a 128 bit window with no more
than 100 consecutive zeros in the data stream. When loss of signal occurs, RLOS register indication and
register status will change. If the RLOS register enable is set high (enabled), the alarm will trigger an interrupt
causing the interrupt pin (INT) to go low. Once the alarm status register has been read, it will automatically
reset upon read (RUR), and the INT pin will return high.
Analog RLOS
Setting the Receiver Inputs to -15dB T1/E1 Short Haul Mode
By setting the receiver inputs to -15dB T1/E1 short haul mode, the equalizer will detect the incoming amplitude
and make adjustments by adding gain up to a maximum of +15dB normalizing the T1/E1 input signal.
NOTE: This is the only setting that refers to cable loss (frequency), not flat loss (resistive).
Once the T1/E1 input signal has been normalized to 0dB by adding the maximum gain (+15dB), the receiver
will declare RLOS if the signal is attenuated by an additional -9dB. The total cable loss at RLOS declaration is
typically -24dB (-15dB + -9dB). A 3dB hysteresis was designed so that transients will not trigger the RLOS to
clear. Therefore, the RLOS will typically clear at a total cable attenuation of -21dB. See Figure 5 for a
simplified diagram.
Setting the Receiver Inputs to -29dB T1/E1 Gain Mode
By setting the receiver inputs to -29dB T1/E1 gain mode, the equalizer will detect the incoming amplitude and
make adjustments by adding gain up to a maximum of +29dB normalizing the T1/E1 input signal.
NOTE: This is the only setting that refers to flat loss (resistive). All other modes refer to cable loss (frequency).
FIGURE 5. SIMPLIFIED DIAGRAM OF -15dB T1/E1 SHORT HAUL MODE AND RLOS CONDITION
Normalized up to +15dB Max
De clare LOS
Clear LOS
-9dB
+3dB
Clear LOS
De clare LOS
+3dB
-9dB
相關PDF資料 |
PDF描述 |
|---|---|
| XRT83VL38IB-F | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| XRT83VSH28IB | IC LIU SH E1 OCTAL 225BGA |
| XRT83VSH314IB-F | IC LIU SH T1/E1/J1 14CH 304TBGA |
| XRT83VSH316IB | IC LIU SH T1/E1/J1 16CH 316STBGA |
| XRT83VSH38IB | IC LIU SH T1/E1/J1 8CH 225BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL38IV | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83VL38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83VL38ES | 功能描述:界面開發工具 Eval System for XRT83L38 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XRT83VL38IB | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83VL38IB-F | 功能描述:外圍驅動器與原件 - PCI Low Power High Perf 8-Chan LIU RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。