參數資料
型號: 2495
廠商: Linear Technology Corporation
英文描述: 16-Bit 8-/16-Channel ツヒ ADC with PGA, Easy Drive and I2C Interface
中文描述: 16位8-/16-ChannelツヒADC,帶PGA巡回賽,輕松驅動和I2C接口
文件頁數: 13/32頁
文件大?。?/td> 558K
代理商: 2495
LTC2495
13
2495f
cancellation does not interfere with the transparent offset
and full-scale auto-calibration and the absolute accuracy
(full scale + offset + linearity + drift) is maintained even
with external RC networks.
Power-Up Sequence
The LTC2495 automatically enters an internal reset state
when the power supply voltage, V
CC
, drops below a
threshold of approximately 2.0V. This feature guarantees
the integrity of the conversion result and input channel
selection.
When V
CC
rises above this threshold, the converter creates
an internal power-on-reset (POR) signal with a duration
of approximately 4ms. The POR signal clears all internal
registers. The conversion immediately following a POR
cycle is performed on the input channels IN
+
= CH0 and
IN
= CH1 with simultaneous 50Hz/60Hz rejection, 1x
output rate, and gain = 1. The first conversion following a
POR cycle is accurate within the specification of the device
if the power supply voltage is restored to (2.7V to 5.5V)
before the end of the POR interval. A new input channel,
rejection mode, speed mode, temperature selection or
gain can be programmed into the device during this first
data input/output cycle.
Reference Voltage Range
This converter accepts a truly differential external reference
voltage. The absolute/common mode voltage range for the
REF
+
and REF
pins covers the entire operating range of
the device (GND to V
CC
). For correct converter operation,
V
REF
must be positive (REF
+
> REF
).
The LTC2495 differential reference input range is 0.1V to
V
CC
. For the simplest operation, REF
+
can be shorted to
V
CC
and REF
can be shorted to GND. The converter out-
put noise is determined by the thermal noise of the front
end circuits and, as such, its value in nanovolts is nearly
constant with reference voltage. A decrease in reference
voltage will not significantly improve the converter’s effec-
tive resolution. On the other hand, a decreased reference
will improve the converter’s overall INL performance.
Input Voltage Range
The analog inputs are truly differential with an absolute,
common mode range for the CH0-CH15 and COM input pins
extending from GND – 0.3V to V
CC
+ 0.3V. Outside these
limits, the ESD protection devices begin to turn on and the
errors due to input leakage current increase rapidly. Within
these limits, the LTC2495 converts the bipolar differential
input signal V
IN
= IN
+
– IN
(where IN
+
and IN
are the
selected input channels), from – FS = – 0.5 V
REF
/Gain
to + FS = 0.5 V
REF
/Gain where V
REF
= REF
+
– REF
.
Outside this range, the converter indicates the overrange
or the underrange condition using distinct output codes
(see Table 1).
Signals applied to the input (CH0-CH15, COM) may extend
300mV below ground and above V
CC
. In order to limit
any fault current, resistors of up to 5k may be added in
series with the input. The effect of series resistance on
the converter accuracy can be evaluated from the curves
presented in the Input Current/Reference Current sections.
In addition, series resistors will introduce a temperature
dependent error due to input leakage current. A 1nA input
leakage current will develop a 1ppm offset error on a 5k
resistor if V
REF
= 5V. This error has a very strong tem-
perature dependency.
MUXOUT/ADCIN
The outputs of the multiplexer (MUXOUTP/MUXOUTN) and
the inputs to the ADC (ADCINP/ADCINN) can be used to
perform input signal conditioning on any of the selected
input channels or simply shorted together for direct
digitization. If an external amplifier is used, the LTC2495
automatically calibrates both the offset and drift of this
circuit and the Easy Drive sampling scheme enables a
wide variety of amplifiers to be used.
In order to achieve optimum performance, if an external
amplifier is not used, short these pins directly together
(ADCINP to MUXOUTP and ADCINN to MUXOUTN) and
minimize their capacitance to ground.
APPLICATIONS INFORMATION
相關PDF資料
PDF描述
249NQ SCHOTTKY RECTIFIER
249NQ135 SCHOTTKY RECTIFIER
249NQ135R SCHOTTKY RECTIFIER
249NQ150 SCHOTTKY RECTIFIER
249NQ150R SCHOTTKY RECTIFIER
相關代理商/技術參數
參數描述
24-9500 制造商:Distributed By MCM 功能描述:CAPACITOR 500V 220UF SNAPRADIAL HIGH-TEMP LOW ESR
249-5005-002 制造商:ITT Interconnect Solutions 功能描述:DPA COAX - Bulk
249-5008-000 制造商:ITT Interconnect Solutions 功能描述:RG58CU 制造商:ITT Interconnect Solutions 功能描述:RG-58 C/U - Bulk 制造商:ITT Interconnect Solutions 功能描述:RG-58 C/U / 249-5008-000 / Rack & Panel
24-9501 制造商:STELLAR LABS 功能描述:3FT SINGLE CHANNEL AUDIO 1 RCARCA M-M
249-5012-000 制造商:ITT Interconnect Solutions 功能描述:DPA C/AXIAL PLUG RG-58 / 249-5012-000 / Rack & Panel