- 您現在的位置：買賣IC網 > PDF目錄371407 > 25C256 (Microchip Technology Inc.) 256K 5.0V SPI Bus Serial EEPROM(4.5~5.5V,256K位,SPI總線串行EEPROM) PDF資料下載
參數資料
| 型號： | 25C256 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 256K 5.0V SPI Bus Serial EEPROM(4.5~5.5V,256K位,SPI總線串行EEPROM) |
| 中文描述： | 256K 5.0V SPI總線串行EEPROM（4.5?5.5V的，256K位和SPI總線串行EEPROM的） |
| 文件頁數： | 91/170頁 |
| 文件大?。?/td> | 4191K |
| 代理商： | 25C256 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁當前第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁
2003 Microchip Technology Inc.
Preliminary
DS40300C-page 89
PIC16F62X
13.3
READING THE EEPROM DATA
MEMORY
To read a data memory location, the user must write the
address to the EEADR register and then set control bit
RD (EECON1<0>). The data is available, in the very
next cycle, in the EEDATA register; therefore it can be
read in the next instruction. EEDATA will hold this value
until another read or until it is written to by the user
(during a write operation).
EXAMPLE 13-1:
DATA EEPROM READ
BSF
MOVLW
MOVWF
BSF
MOVF
BCF
STATUS, RP0
CONFIG_ADDR
EEADR
EECON1, RD
EEDATA, W
STATUS, RP0
; Bank 1
;
; Address to read
; EE Read
; W = EEDATA
; Bank 0
13.4
WRITING TO THE EEPROM DATA
MEMORY
To write an EEPROM data location, the user must first
write the address to the EEADR register and the data
to the EEDATA register. Then the user must follow a
specific sequence to initiate the write for each byte.
EXAMPLE 13-2:
DATA EEPROM WRITE
BSF
BSF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
BSF
STATUS, RP0
EECON1, WREN
INTCON, GIE
55h
EECON2
AAh
EECON2
EECON1,WR
; Bank 1
; Enable write
; Disable INTs.
;
; Write 55h
;
; Write AAh
; Set WR bit
; begin write
; Enable INTs
.
INTCON, GIE
The write will not initiate if the above sequence is not
exactly followed (write 55h to EECON2, write AAh to
EECON2, then set WR bit) for each byte. We strongly
recommend that interrupts be disabled during this
code segment. A cycle count is executed during the
required sequence. Any number that is not equal to the
required cycles to execute the required sequence will
cause the data not to be written into the EEPROM.
Additionally, the WREN bit in EECON1 must be set to
enable write. This mechanism prevents accidental
writes to data EEPROM due to errant (unexpected)
code execution (i.e., lost programs). The user should
keep the WREN bit clear at all times, except when
updating EEPROM. The WREN bit is not cleared
by hardware.
After a write sequence has been initiated, clearing the
WREN bit will not affect this write cycle. The WR bit will
be inhibited from being set unless the WREN bit is set.
At the completion of the write cycle, the WR bit is
cleared in hardware and the EE Write Complete
Interrupt Flag bit (EEIF) is set. The user can either
enable this interrupt or poll this bit. The EEIF bit in the
PIR1 registers must be cleared by software.
13.5
WRITE VERIFY
Depending on the application, good programming
practice may dictate that the value written to the Data
EEPROM should be verified (Example 13-3) to the
desired value to be written. This should be used in
applications where an EEPROM bit will be stressed
near the specification limit.
EXAMPLE 13-3:
WRITE VERIFY
BSF STATUS, RP0
MOVF EEDATA, W
BSF EECON1, RD
; Bank 1
; Read the
; value written
;
; Is the value written (in W reg) and
; read (in EEDATA) the same
;
SUBWF EEDATA, W
BCF
STATUS, RP0
BTFSS STATUS, Z
GOTO WRITE_ERR
:
:
;
; Bank0
; Is difference 0
; NO, Write error
; YES, Good write
; Continue program
13.6
PROTECTION AGAINST
SPURIOUS WRITE
There are conditions when the device may not want to
write to the data EEPROM memory. To protect against
spurious EEPROM writes, various mechanisms have
been built in. On power-up, WREN is cleared. Also, the
Power-up
Timer
(72
EEPROM write.
ms
duration)
prevents
The write initiate sequence, and the WREN bit together
help prevent an accidental write during brown-out,
power glitch, or software malfunction.
13.7
DATA EEPROM OPERATION
DURING CODE PROTECT
When the device is code protected, the CPU is able to
read and write unscrambled data to the Data
EEPROM.
R
S
相關PDF資料 |
PDF描述 |
|---|---|
| 25C160 | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 25C080 | 8K 5.0V SPI Bus Serial EEPROM(4.5~5.5V,3MHz,8K位,10M次可自定時擦寫周期,EEPROM) |
| 25C320 | 32K 5.0V SPI Bus Serial EEPROM |
| 25C320T | 32K SPI Bus Serial EEPROM |
| 25C320X | SENSOR REFLECTIVE OBJECT 50MA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 25C256KI | 制造商:CSI 功能描述: |
| 25C25Z450T | 制造商:QUAM NICHOLS 功能描述:Industrial Intercom ;RoHS Compliant: Yes |
| 25C25Z450TK | 制造商:QUAM NICHOLS 功能描述:2 1/2 INCH 45 OHM OUTDOOR TREATED SPEAKER |
| 25C25Z80T | 制造商:Quam-Nichols Manufacturing 功能描述:Loudspeaker 制造商:QUAM NICHOLS 功能描述:Loudspeaker ;RoHS Compliant: Yes |
| 25C25Z80TK | 制造商:QUAM 功能描述: 制造商:Quam-Nichols Manufacturing 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。