- 您現在的位置：買賣IC網 > PDF目錄10049 > AD9640ABCPZ-80 (Analog Devices Inc)IC ADC 14BIT 80MSPS 64LFCSP PDF資料下載
參數資料
| 型號： | AD9640ABCPZ-80 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 37/52頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 80MSPS 64LFCSP |
| 設計資源： | Interfacing ADL5534 to AD9640 High Speed ADC (CN0049) |
| 標準包裝： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 80M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 492mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 4 個單端，單極；2 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
AD9640
Rev. B | Page 42 of 52
MEMORY MAP
READING THE MEMORY MAP TABLE
Each row in the memory map table has eight bit locations. The
memory map is roughly divided into four sections: chip configura-
tion and ID register map (Address 0x00 to Address 0x02); ADC
setup, control, and test (Address 0x08 to Address 0x25); the
channel index and transfer register map (Address 0x05 to
Address 0xFF); and digital feature control (Address 0x100 to
Address 0x11B).
Starting from the right hand column, the memory map register
in Table 25 documents the default hex value for each hex address
shown. The column with the heading Bit 7 (MSB) is the start
of the default hex value given. For example, Address 0x18, VREF
select, has a hex default value of 0xC0. This means Bit 7 = 1,
Bit 6 = 1, and the remaining bits are 0s. This setting is the default
reference selection setting. The default value uses a 2.0 V peak-
to-peak reference. For more information on this function and
others, see the AN-877 Application Note, Interfacing to High Speed
ADCs via SPI. This document details the functions controlled by
Register 0x00 to Register 0xFF. The remaining registers, from
Register 0x100 to Register 0x11B, are documented in the Memory
Map Register Description section.
Open Locations
All address and bit locations that are not included in Table 25
are currently not supported for this device. Unused bits of a
valid address location should be written with 0s. Writing to these
locations is required only when part of an address location is
open (for example, Address 0x18). If the entire address location
is open (for example, Address 0x13), this address location should
not be written.
Default Values
Coming out of reset, critical registers are loaded with default
values. The default values for the registers are given in the
memory map register table, Table 25.
Logic Levels
An explanation of logic level terminology follows:
“Bit is set” is synonymous with “Bit is set to Logic 1” or
“Writing Logic 1 for the bit.”
“Clear a bit” is synonymous with “Bit is set to Logic 0” or
“Writing Logic 0 for the bit.”
Transfer Register Map
Address 0x08 to Address 0x18 are shadowed. Writes to these
addresses do not affect part operation until a transfer command
is issued by writing 0x01 to Address 0xFF, setting the transfer bit.
This allows these registers to be updated internally and simulta-
neously when the transfer bit is set. The internal update takes
place when the transfer bit is set, and the bit autoclears.
Channel-Specific Registers
Some channel setup functions, such as the signal monitor
thresholds, can be programmed differently for each channel.
In these cases, channel address locations are internally duplicated
for each channel. These registers are designated in the parameter
name column of Table 25 as local registers. These local registers
can be accessed by setting the appropriate Channel A or Channel B
bits in Register 0x05. If both bits are set, the subsequent write
affects the registers of both channels. In a read cycle, only
Channel A or Channel B should be set to read one of the two
registers. If both bits are set during an SPI read cycle, the part
returns the value for Channel A. Registers designated as global
in the parameter name column of Table 25 affect the entire part
or the channel features where independent settings are not
allowed between the channels. The settings in Register 0x05
do not affect the global registers.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM5170AP-REEL | IC TXRX RS232/423 OCTAL 28PLCC |
| MS27508E12A98S | CONN RCPT 10POS BOX MNT W/SCKT |
| GTC06AF-16-11P | CONN PLUG 2POS STRAIGHT W/PINS |
| MS27508E22B55PA | CONN RCPT 55POS BOX MNT W/PINS |
| MS27467E9A35S | CONN PLUG 6POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9640ABCPZRL7-105 | 功能描述:模數轉換器 - ADC 14Bit 105Msps Dual 1.8V PB Free ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9640ABCPZRL7-125 | 功能描述:14 Bit Analog to Digital Converter 2 Input 2 Pipelined 64-LFCSP-VQ (9x9) 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:在售 位數:14 采樣率（每秒）:125M 輸入數:2 輸入類型:差分，單端 數據接口:并聯 配置:S/H-ADC 無線電 - S/H:ADC:1:1 A/D 轉換器數:2 架構:管線 參考類型:外部， 內部 電壓 - 電源，模擬:1.7 V ~ 1.9 V 電壓 - 電源，數字:1.7 V ~ 1.9 V 特性:同步采樣 工作溫度:-40°C ~ 85°C 封裝/外殼:64-VFQFN 裸露焊盤，CSP 供應商器件封裝:64-LFCSP-VQ（9x9） 標準包裝:750 |
| AD9640ABCPZRL7-80 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 80/105/125/150 MSPS, 1.8 V Dual Analog-to-Digital Converter |
| AD9640BCPZ-105 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 105Msps 14-bit Parallel 64-Pin LFCSP EP 制造商:Analog Devices 功能描述:IC ADC 14BIT 105MSPS LFCSP-64 |
| AD9640BCPZ-125 | 制造商:Analog Devices 功能描述:IC ADC 14BIT 125MSPS LFCSP-64 制造商:Analog Devices 功能描述:IC, ADC, 14BIT, 125MSPS, LFCSP-64, Resolution (Bits):14bit, Sampling Rate:150MSP |
發布緊急采購，3分鐘左右您將得到回復。