參數資料
型號: ADF4193WCCPZ-RL7
廠商: Analog Devices Inc
文件頁數: 17/32頁
文件大?。?/td> 0K
描述: IC PLL FREQ SYNTHESIZER 32LFCSP
標準包裝: 1,500
類型: 時鐘/頻率合成器,RF
PLL:
輸入: CMOS,TTL
輸出: 時鐘
電路數: 1
比率 - 輸入:輸出: 2:1
差分 - 輸入:輸出: 是/無
頻率 - 最大: 3.5GHz
除法器/乘法器: 是/是
電源電壓: 2.7 V ~ 3.3 V
工作溫度: -40°C ~ 105°C
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤,CSP
供應商設備封裝: 32-LFCSP-VQ
包裝: 帶卷 (TR)
ADF4193
Data Sheet
Rev. F | Page 24 of 32
switches opened, and thus the phase swing that occurs when the
BW is reduced can be minimized.
With dither off, the fractional spur pattern due to the SDM’s
quantization noise also depends on the phase word the modulator
is seeded with. Tables of optimized FRAC and phase values for
popular SW1/SW2 and ICP timer settings can be down-loaded
from the ADF4193 product page. If making use of a phase table,
first write phase to double buffered Register R2, then write the
INT and FRAC to R0.
Avoiding Integer Boundary Channels
A further option when programming a new frequency involves
a write to Register R1 to avoid integer boundary spurs. If it is
found that the integer boundary spur level is too high, an
option is to move the integer boundary away from the desired
channel by reprogramming the R divider to select a different
PFD frequency. For example, if REFIN = 104 MHz and R = 4 for
a 26 MHz PFD frequency and MOD = 130 for 200 kHz steps,
the frequency channel at 910.2 MHz has a 200 kHz integer
boundary spur because it is 200 kHz offset from 35 × 26 MHz.
An alternative way to synthesize this channel is to set R = 5 for a
20.8 MHz PFD reference and MOD = 104 for 200 kHz steps.
The 910.2 MHz channel is now 5 MHz offset from the nearest
integer multiple of 20.8 MHz and the 5 MHz beat note spurs are
well attenuated by the loop. Setting double buffered Bit R1 [23] = 1
(CP ADJ bit) increases the charge pump current by 25%, which
compensates for the 25% increase in N with the change to the
20.8 MHz PFD frequency. This maintains constant loop dynamics
and settling time performance for jumps between the two PFD
frequencies. The CP ADJ bit should be cleared again when jumping
back to 26 MHz-based channels.
The Register R1 settings necessary for integer boundary spur
avoidance are all double buffered and do not become active on
the chip until the next write to Register R0. Register R0 should
always be the last register written to when programming a new
frequency.
Serial Interface Activity
The serial interface activity when programming the R2 or R1
registers causes no noticeable disturbance to the synthesizers
settled phase or degradation in its frequency spectrum. Therefore,
in a GSM application, it can be performed during the active
part of the data burst. Because it takes just 10.2 s to program
the three registers, R2, R1, and R0, with the 6.5 MHz serial
interface clock rate typically used, this programming can also be
performed during the previous guard period with the LE edge
to latch in the R0 data delayed until it’s time to switch
frequency.
相關PDF資料
PDF描述
V110A8H200BL3 CONVERTER MOD DC/DC 8V 200W
V110A8H200BG CONVERTER MOD DC/DC 8V 200W
VI-B7W-MY-F4 CONVERTER MOD DC/DC 5.5V 50W
VI-B7W-MY-F3 CONVERTER MOD DC/DC 5.5V 50W
MS27472E24F29S CONN RCPT 29POS WALL MT W/SCKT
相關代理商/技術參數
參數描述
ADF4196 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Phase Noise, Fast Settling, 6 GHz
ADF4196BCPZ 制造商:Analog Devices 功能描述:IC PLL SYNTHESIZER 32LFCSP 制造商:Analog Devices 功能描述:IC, PLL SYNTHESIZER, 32LFCSP
ADF4196BCPZ-RL7 制造商:Analog Devices 功能描述:
ADF4206 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual RF PLL Frequency Synthesizers
ADF4206BRU 制造商:Analog Devices 功能描述:PLL Frequency Synthesizer Dual 16-Pin TSSOP