DMA Handshake See Table 18 and Figure 21. These specifications describe the three DMA handshake modes. In all three mod" />
參數資料
型號： ADSP-21160NCBZ-100
廠商： Analog Devices Inc
文件頁數： 26/48頁
文件大?。?/td> 0K
描述： IC DSP CONTROLLER 32BIT 400-PBGA
產品培訓模塊： SHARC Processor Overview
標準包裝： 1
系列： SHARC®
類型： 浮點
接口： 主機接口，連接端口，串行端口
時鐘速率： 100MHz
非易失內存： 外部
芯片上RAM： 512kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 1.90V
工作溫度： -40°C ~ 100°C
安裝類型： 表面貼裝
封裝/外殼： 400-BBGA
供應商設備封裝： 400-PBGA（27x27）
包裝： 托盤
ADSP-21160N
–32–
REV. 0
DMA Handshake
See Table 18 and Figure 21. These specifications describe the
three DMA handshake modes. In all three modes,
DMARx is
used to initiate transfers. For handshake mode,
DMAGx controls
the latching or enabling of data externally. For external hand-
shake mode, the data transfer is controlled by the ADDR31–0,
RDx, WRx, PAGE, MS3–0, ACK, and DMAGx signals. For
Paced Master mode, the data transfer is controlled by
ADDR31–0,
RDx, WRx, MS3–0, and ACK (not DMAG). For
Paced Master mode, the Memory Read-Bus Master, Memory
Write-Bus Master, and Synchronous Read/Write-Bus Master
timing specifications for ADDR31–0,
RDx, WRx, MS3–0,
PAGE, DATA63–0, and ACK also apply.
Table 18. DMA Handshake
Parameter
Min
Max
Unit
Timing Requirements
tSDRC
DMARx Setup Before CLKIN1
3ns
tWDR
DMARx Width Low (Nonsynchronous)2
0.5tCCLK+2.5
ns
tSDATDGL
Data Setup After
DMAGx Low3
tCK –0.5tCCLK –7
ns
tHDATIDG
Data Hold After
DMAGx High
2
ns
tDATDRH
Data Valid After
DMARx High3
tCK+3
ns
tDMARLL
DMARx Low Edge to Low Edge4
tCK
ns
tDMARH
DMARx Width High2
0.5tCCLK+1
ns
Switching Characteristics
tDDGL
DMAGx Low Delay After CLKIN
0.25tCCLK+1
0.25tCCLK+9
ns
tWDGH
DMAGx High Width
0.5tCCLK –1 +HI
ns
tWDGL
DMAGx Low Width
tCK –0.5tCCLK –1
ns
tHDGC
DMAGx High Delay After CLKIN
tCK – 0.25tCCLK+1.5
tCK – 0.25tCCLK+9
ns
tVDATDGH
Data Valid Before
DMAGx High5
tCK – 0.25tCCLK –8
tCK – 0.25tCCLK+5
ns
tDATRDGH
Data Disable After
DMAGx High6
0.25tCCLK – 3
0.25tCCLK+1.5
ns
tDGWRL
WRx Low Before DMAGx Low
–1.5
2
ns
tDGWRH
DMAGx Low Before WRx High
tCK –0.5tCCLK –2+ W
ns
tDGWRR
WRx High Before DMAGx High7
–1.5
2
ns
tDGRDL
RDx Low Before DMAGx Low
–1.5
2
ns
tDRDGH
RDx Low Before DMAGx High
tCK –0.5tCCLK–2+W
ns
tDGRDR
RDx High Before DMAGx High7
–1.5
2
ns
tDGWR
DMAGx High to WRx, RDx, DMAGx
Low
0.5tCCLK –2 +HI
ns
tDADGH
Address/Select Valid to
DMAGx High
15.5
ns
tDDGHA
Address/Select Hold after
DMAGx High
1
ns
W = (number of wait states specified in WAIT register)
tCK.
HI = tCK (if data bus idle cycle occurs, as specified in WAIT register; otherwise HI = 0).
1 Only required for recognition in the current cycle.
2 Maximum throughput using
DMARx/DMAGx handshaking equals tWDR + tDMARH = (0.5tCCLK+1) + (0.5tCCLK+1)=10.0 ns (100 MHz). This throughput
limit applies to non-synchronous access mode only.
3 tSDATDGL is the data setup requirement if DMARx is not being used to hold off completion of a write. Otherwise, if DMARx low holds off completion of
the write, the data can be driven tDATDRH after DMARx is brought high.
4 Use tDMARLL if DMARx transitions synchronous with CLKIN. Otherwise, use tWDR and tDMARH.
5 tVDATDGH is valid if DMARx is not being used to hold off completion of a read. If DMARx is used to prolong the read, then
tVDATDGH =tCK –.25tCCLK –8+ (n × tCK) where n equals the number of extra cycles that the access is prolonged.
6 See Example System Hold Time Calculation on Page 41 for calculation of hold times given capacitive and dc loads.
7 This parameter applies for synchronous access mode only.
相關PDF資料
PDF描述
171-009-213R021 CONN DB9 FEMALE DIP SLD NICKEL
VE-2WM-CY-F4 CONVERTER MOD DC/DC 10V 50W
ADSP-21062KSZ-133 IC DSP CONTROLLER 32BIT 240MQFP
TAJC684K050SNJ CAP TANT 0.68UF 50V 10% 2312
EEM10DRKF CONN EDGECARD 20POS DIP .156 SLD
相關代理商/技術參數
參數描述
ADSP-21160NCE-100 制造商:Analog Devices 功能描述:
ADSP-21160NKB-100 功能描述:IC DSP CONTROLLER 32BIT 400BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
ADSP-21160NKB-95 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer
ADSP-21160NKB-X 制造商:Analog Devices 功能描述:
ADSP-21160NKBZ-100 功能描述:IC DSP CONTROLLER 32BIT 400-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*