參數資料
型號： ADV7183ABST
廠商： ANALOG DEVICES INC
元件分類： 顏色信號轉換
英文描述： Multiformat SDTV Video Decoder
中文描述： COLOR SIGNAL DECODER, PQFP80
封裝： LEAD FREE, MS-026-BEC, LQFP-80
文件頁數： 57/104頁
文件大?。?/td> 894K
代理商： ADV7183ABST
ADV7183A
Table 152. Data Byte Allocation
Raw Information Bytes
Retrieved from the Video Line
1
4
1
4
0
2
0
2
Rev. A | Page 57 of 104
2×
GDECAD
0
1
0
1
User Data-Words
(Including Padding)
8
4
4
4
Padding Bytes
0
0
0
2
DC[1:0]
10
01
01
01
Notes
DID. The data identification value is 140h (10-bit value).
Care has been taken that in 8-bit systems, the 2 LSBs do
not carry vital information.
EP and !EP. The EP bit is set to ensure even parity on the
data-word D[8:0]. Even parity means there will always be
an even number of 1s within the D[8:0] bit arrangement.
This includes the EP bit. !EP describes the logic inverse of
EP and is output on D[9]. The !EP is output to ensure that
the reserved codes of 00 and FF cannot happen.
EF. Even field identifier. EF = 1 indicates that the data was
recovered from a video line on an even field.
2X. This bit indicates whether the data sliced was in
Gemstar 1× or 2× format. A high indicates 2× format.
line[3:0]. This entry provides a code that is unique for each
of the possible 16 source lines of video from which
Gemstar data may have been retrieved. Please refer to Table
164 and Table 165.
DC[1:0]. Data count value. The number of User Data
Words in the packet divided by 4. The number of user data
words (UDW) in any packet must be an integral number of
4. Padding is required at the end, if necessary
12
. See to Table
152.
The 2X bit determines whether the raw information
retrieved from the video line was 2 or 4 bytes. The state of
the GDECAD bit affects whether the bytes are transmitted
12
Requirement as set in ITU-R BT.1364.
straight (i.e., two bytes transmitted as two bytes) or
whether they are split into nibbles (i.e., two bytes
transmitted as four half bytes). Padding bytes are then
added where necessary.
CS[8:2]. The checksum is provided to determine the
integrity of the ancillary data packet. It is calculated by
summing up D[8:2] of DID, SDID, the Data Count byte,
and all UDWs, and ignoring any overflow during the
summation. Since all data bytes that are used to calculate
the checksum have their 2 LSBs set to 0, the CS[1:0] bits are
also always 0.
!CS[8] describes the logic inversion of CS[8]. The value
!CS[8] is included in the checksum entry of the data packet
to ensure that the reserved values of 0x00 and 0xFF do not
occur.
Table 153 to Table 156 outline the possible data packages.
Gemstar 2× Format, Half-Byte Output Mode
Half-byte output mode is selected by setting CDECAD = 0; full-
byte output mode is selected by setting CDECAD = 1. See the
GDECAD Gemstar Decode Ancillary Data Format (SDP),
Address 0x4C, [0] section.
Gemstar 1× Format
Half-byte output mode is selected by setting CDECAD = 0, full-
byte output mode is selected by setting CDECAD = 1. See the
GDECAD Gemstar Decode Ancillary Data Format (SDP),
Address 0x4C, [0] section.
相關PDF資料
PDF描述
ADV7183AKST Multiformat SDTV Video Decoder
ADV7330 Multiformat 11-Bit Triple DAC Video Encoder
ADV7330KST Multiformat 11-Bit Triple DAC Video Encoder
ADXL321 Small and Thin 18 g Accelerometer
ADXL321EB Small and Thin 18 g Accelerometer
相關代理商/技術參數
參數描述
ADV7183AKST 制造商:Analog Devices 功能描述:MULTIFORMAT SDTV VIDEO DECODER 制造商:Rochester Electronics LLC 功能描述:10BIT NTSC/PAL/SECAMVIDDECOD I.C - Tape and Reel 制造商:Analog Devices 功能描述:IC VIDEO ENCODER
ADV7183AKST-U1 制造商:Analog Devices 功能描述:VID DECODER 80LQFP - Bulk
ADV7183AKST-X2 制造商:Analog Devices 功能描述:VID DECODER - Bulk
ADV7183AXST 制造商:Analog Devices 功能描述:VIDEO DECODER I.C. - Bulk
ADV7183AXST-X2 制造商:Analog Devices 功能描述:VIDEO DECODER I.C. - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*