Revision 17 1-7 User Nonvolatile FlashROM IGLOO nano devices have 1 kbit of on-chip, user-accessible, nonv" />
參數資料
型號: AGLN250V5-CSG81I
廠商: Microsemi SoC
文件頁數: 35/150頁
文件大?。?/td> 0K
描述: IC FPGA NANO 1KB 250K 81-CSP
標準包裝: 640
系列: IGLOO nano
邏輯元件/單元數: 6144
RAM 位總計: 36864
輸入/輸出數: 60
門數: 250000
電源電壓: 1.425 V ~ 1.575 V
安裝類型: 表面貼裝
工作溫度: -40°C ~ 85°C
封裝/外殼: 81-WFBGA,CSBGA
供應商設備封裝: 81-CSP(5x5)
IGLOO nano Low Power Flash FPGAs
Revision 17
1-7
User Nonvolatile FlashROM
IGLOO nano devices have 1 kbit of on-chip, user-accessible, nonvolatile FlashROM. The FlashROM can
be used in diverse system applications:
Internet protocol addressing (wireless or fixed)
System calibration settings
Device serialization and/or inventory control
Subscription-based business models (for example, set-top boxes)
Secure key storage for secure communications algorithms
Asset management/tracking
Date stamping
Version management
The FlashROM is written using the standard IGLOO nano IEEE 1532 JTAG programming interface. The
core can be individually programmed (erased and written), and on-chip AES decryption can be used
selectively to securely load data over public networks (except in the AGLN030 and smaller devices), as
in security keys stored in the FlashROM for a user design.
The FlashROM can be programmed via the JTAG programming interface, and its contents can be read
back either through the JTAG programming interface or via direct FPGA core addressing. Note that the
FlashROM can only be programmed from the JTAG interface and cannot be programmed from the
internal logic array.
The FlashROM is programmed as 8 banks of 128 bits; however, reading is performed on a byte-by-byte
basis using a synchronous interface. A 7-bit address from the FPGA core defines which of the 8 banks
and which of the 16 bytes within that bank are being read. The three most significant bits (MSBs) of the
FlashROM address determine the bank, and the four least significant bits (LSBs) of the FlashROM
address define the byte.
The IGLOO nano development software solutions, Libero System-on-Chip (SoC) and Designer, have
extensive support for the FlashROM. One such feature is auto-generation of sequential programming
files for applications requiring a unique serial number in each part. Another feature enables the inclusion
of static data for system version control. Data for the FlashROM can be generated quickly and easily
using Microsemi Libero SoC and Designer software tools. Comprehensive programming file support is
also included to allow for easy programming of large numbers of parts with differing FlashROM contents.
SRAM and FIFO
IGLOO nano devices (except the AGLN030 and smaller devices) have embedded SRAM blocks along
their north and south sides. Each variable-aspect-ratio SRAM block is 4,608 bits in size. Available
memory configurations are 256×18, 512×9, 1k×4, 2k×2, and 4k×1 bits. The individual blocks have
independent read and write ports that can be configured with different bit widths on each port. For
example, data can be sent through a 4-bit port and read as a single bitstream. The embedded SRAM
blocks can be initialized via the device JTAG port (ROM emulation mode) using the UJTAG macro
(except in the AGLN030 and smaller devices).
In addition, every SRAM block has an embedded FIFO control unit. The control unit allows the SRAM
block to be configured as a synchronous FIFO without using additional core VersaTiles. The FIFO width
and depth are programmable. The FIFO also features programmable Almost Empty (AEMPTY) and
Almost Full (AFULL) flags in addition to the normal Empty and Full flags. The embedded FIFO control
unit contains the counters necessary for generation of the read and write address pointers. The
embedded SRAM/FIFO blocks can be cascaded to create larger configurations.
PLL and CCC
Higher density IGLOO nano devices using either the two I/O bank or four I/O bank architectures provide
designers with very flexible clock conditioning capabilities. AGLN060, AGLN125, and AGLN250 contain
six CCCs. One CCC (center west side) has a PLL. The AGLN030 and smaller devices use different
CCCs in their architecture (CCC-GL). These CCC-GLs contain a global MUX but do not have any PLLs
or programmable delays.
For devices using the six CCC block architecture, these are located at the four corners and the centers of
the east and west sides. All six CCC blocks are usable; the four corner CCCs and the east CCC allow
simple clock delay operations as well as clock spine access.
相關PDF資料
PDF描述
AGLN250V5-ZCSG81I IC FPGA NANO 1KB 250K 81-CSP
AGL125V5-CSG196I IC FPGA 1KB FLASH 125K 196-CSP
AGL125V5-CS196I IC FPGA 1KB FLASH 125K 196-CSP
A3P060-2FG144I IC FPGA 1KB FLASH 60K 144-FBGA
ABM43DSEN-S13 CONN EDGECARD EXTEND 86POS .156
相關代理商/技術參數
參數描述
AGLN250V5-DIELOT 制造商:Microsemi Corporation 功能描述:AGLN250V5-DIELOT - Gel-pak, waffle pack, wafer, diced wafer on film 制造商:Microsemi SOC Products Group 功能描述:AGLN250V5-DIELOT - Gel-pak, waffle pack, wafer, diced wafer on film
AGLN250V5-QNG100 制造商:Microsemi Corporation 功能描述:FPGA IGLOO NANO FAMILY 250K GATES 130NM (CMOS) TECHNOLOGY 1. - Trays 制造商:Microsemi SOC Products Group 功能描述:FPGA IGLOO NANO FAMILY 250K GATES 130NM (CMOS) TECHNOLOGY 1. - Trays
AGLN250V5-QNG100I 制造商:Microsemi Corporation 功能描述:FPGA IGLOO NANO 250K GATES IND 130NM 1.5V 100QFN - Trays 制造商:Microsemi SOC Products Group 功能描述:FPGA IGLOO NANO 250K GATES IND 130NM 1.5V 100QFN - Trays
AGLN250V5-VQ100 功能描述:IC FPGA NANO 1KB 250K 100VQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA,CSBGA 供應商設備封裝:289-CSP(14x14)
AGLN250V5-VQ100I 功能描述:IC FPGA NANO 1KB 250K 100VQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA(現場可編程門陣列) 系列:IGLOO nano 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA,CSBGA 供應商設備封裝:289-CSP(14x14)