- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C961AKIW (ADVANCED MICRO DEVICES INC) PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA PDF資料下載
參數資料
| 型號： | AM79C961AKIW |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
| 中文描述： | 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP132 |
| 封裝： | PLASTIC, QFP-132 |
| 文件頁數： | 43/206頁 |
| 文件大?。?/td> | 1507K |
| 代理商： | AM79C961AKIW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁
Am79C961A
43
FUNCTIONAL DESCRIPTION
PCMCIA Operation
When a PCMCIA card is first plugged into a PCMCIA
host, all PCMCIA cards respond as a memory only
device. In the PCMCIA standard there are two memory
spaces, common memory and attribute memory. The
REG pin determines which memory space is selected.
After the host detects that the PCMCIA card is inserted,
the host reads a section of the attribute memory called the
CIS (Card Information Structure) which provides
configuration information about the inserted card. The
attribute memory is a byte wide memory which is only
addressable on even bytes. Consequently, odd byte
accesses are not defined for attribute memory. Mapped in
the CIS area are four Card Configuration Registers which
are physically located inside the PCnet-ISA II device. In
the PCnet-ISA II device there are four registers which are
located at decimal byte address 1008, 1010, 1012 and
1014, respectively. Inside the CIS data structure, there is
information which provides the base address of the Card
Configuration Registers.
Inside first Card Configuration Register is a configura-
tion index region which allows programming the device
to support I/O accesses. The PCnet-ISA II supports
PCMCIA
’
s Independent I/O address window mecha-
nism. When I/O Enable is set in the CCR 0 register the
PCnet-ISA II controller will respond to I/O commands.
The lower 5 address bits decode register accesses.
The PCMCIA host is expected to decode I/O address
bits 6 and above and only assert CE1 and/or CE2 if the
upper I/O address lines match. After the host has
mapped the PCMCIA
’
s card resources to the system,
the card should be visible by the system and the driver
may be loaded.
Serial EEPROM Support
The Serial EEPROM is not required in PCMCIA mode
but can be used to hold the contents of the IEEE address
EEPROM. For cost purposes, it is recommended to
place the IEEE address in the CIS (Card Information
Structure) Attribute Memory.
Flash Memory Map
The PCnet-ISA II device supports either a single Flash or
EPROM device. The external flash device contains the
CIS area as well as an area located in common memory
used to hold software drivers. The attribute memory ori-
gin is located at byte 0. The common memory region is
accessed when REG is deasserted and an access to
common memory occurs. SMAM is normally connected
to an upper address line on the PCMCIA card. When a
high order address is asserted the Flash Memory will be
selected. Accesses to common memory when SMAM is
low will access the Shared RAM when Shared Memory
mode is selected. If Programmed I/O mode is used, the
SMAM can be tied high which will result in the Flash
’
s
base address being mapped to location zero.
Flash Memory Programming
The Flash Memory device can be read at anytime. In
order to program the flash device, the APWEN bit must
be set in ISACSR2 register to allow write operations to
the Flash or non-volatile EEPROM device.
Shared Memory vs. Programmed I/O
Implications
The PCnet-ISA II controller in PCMCIA modes allows for
the local packet buffer memory to be mapped into com-
mon memory or indirectly accessed through I/O ac-
cesses. If shared memory is chosen, the local SRAM will
be mapped as a memory resource. Consequently, the
CIS will have to indicate this requirement to the system.
If Programmed I/O is used no additional memory re-
sources will be required to be allocated by the system.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C961AVCW | PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
| AM79C961AVIW | PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
| Am79C965A | PCnet?-32 Single-Chip 32-Bit Ethernet Controller |
| AM79C970AKCW | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AKC | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C961APDLUTS | 制造商:Advanced Micro Devices 功能描述: |
| AM79C961AVC | 制造商:Rochester Electronics LLC 功能描述: 制造商:Advanced Micro Devices 功能描述:LAN Node Controller, 144 Pin, TQFP |
| AM79C961AVC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller |
| AM79C961AVC\\W | 制造商:Rochester Electronics LLC 功能描述: |
| AM79C961AVC\W | 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。