- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C961AKIW (ADVANCED MICRO DEVICES INC) PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA PDF資料下載
參數資料
| 型號： | AM79C961AKIW |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
| 中文描述： | 2 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PQFP132 |
| 封裝： | PLASTIC, QFP-132 |
| 文件頁數： | 92/206頁 |
| 文件大?。?/td> | 1507K |
| 代理商： | AM79C961AKIW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁當前第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁
92
Am79C961A
Abnormal network conditions include:
I
Loss of carrier
I
Late collision
I
SQE Test Error (Does not apply to 10BASE-T port.)
These should not occur on a correctly configured 802.3
network, and will be reported if they do.
When an error occurs in the middle of a multi-buffer
frame transmission, the error status will be written in
the current descriptor. The OWN bit(s) in the subse-
quent descriptor(s) will be reset until the STP (the next
frame) is found.
Loss of Carrier
A loss of carrier condition will be reported if the PC-
net-ISA II controller cannot observe receive activity
while it is transmitting on the AUI port. After the PC-
net-ISA II controller initiates a transmission, it will ex-
pect to see data
“
looped back
”
on the DI
±
pair. This will
internally generate a
“
carrier sense,
”
indicating that the
integrity of the data path to and from the MAU is intact,
and that the MAU is operating correctly. This
“
carrier
sense
”
signal must be asserted before the end of the
transmission. If
“
carrier sense
”
does not become active
in response to the data transmission, or becomes inac-
tive before the end of transmission, the loss of carrier
(LCAR) error bit will be set in TMD2 after the frame has
been transmitted. The frame will not be re-tried on the
basis of an LCAR error. In 10BASE-T mode LCAR will
indicate that Jabber or Link Fail state has occurred.
Late Collision
A late collision will be reported if a collision condition
occurs after one slot time (512 bit times) after the trans-
mit process was initiated (first bit of preamble com-
menced). The PCnet-ISA II controller will abandon the
transmit process for the particular frame, set Late Col-
lision (LCOL) in the associated TMD3, and process the
next transmit frame in the ring. Frames experiencing a
late collision will not be re-tried. Recovery from this
condition must be performed by upper-layer software.
SQE Test Error
During the inter packet gap time following the comple-
tion of a transmitted message, the AUI CI
±
pair is
asserted by some transceivers as a self-test. The inte-
gral Manchester Encoder/Decoder will expect the SQE
Test Message (nominal 10 MHz sequence) to be
returned via the CI
±
pair within a 40 network bit time
period after DI
±
pair goes inactive. If the CI
±
inputs are
not asserted within the 40 network bit time period fol-
lowing the completion of transmission, then the PC-
net-ISA II controller will set the CERR bit in CSR0.
CERR will be asserted in 10BASE-T mode after trans-
mit if T-MAU is in Link Fail state. CERR will never cause
INTR to be activated. It will, however, set the ERR bit in
CSR0.
Host related transmit exception conditions include
BUFF and UFLO as described in the Transmit Descrip-
tor section.
Receive Operation
The receive operation and features of the PCnet-ISA II
controller are controlled by programmable options.
Receive Function Programming
Automatic pad field stripping is enabled by setting the
ASTRP_RCV bit in CSR4; this can provide flexibility in
the reception of messages using the 802.3 frame format.
All receive frames can be accepted by setting the
PROM bit in CSR15. When PROM is set, the PC-
net-ISA II controller will attempt to receive all mes-
sages, subject to minimum frame enforcement.
Promiscuous mode overrides the effect of the Disable
Receive Broadcast bit on receiving broadcast frames.
The point at which the BMU will start to transfer data
from the receive FIFO to buffer memory is controlled by
the RCVFW bits in CSR80. The default established
during reset is 10b, which sets the threshold flag at 64
bytes empty.
Automatic Pad Stripping
During reception of an 802.3 frame the pad field can be
stripped automatically. ASTRP_RCV (bit 10 in CSR4) =
1 enables the automatic pad stripping feature. The pad
field will be stripped before the frame is passed to the
FIFO, thus preserving FIFO space for additional
frames. The FCS field will also be stripped, since it is
computed at the transmitting station based on the data
and pad field characters, and will be invalid for a
receive frame that has had the pad characters stripped.
The number of bytes to be stripped is calculated from
the embedded length field (as defined in the IEEE
802.3 definition) contained in the frame. The length
indicates the actual number of LLC data bytes con-
tained in the message. Any received frame which con-
tains a length field less than 46 bytes will have the pad
field stripped (if ASTRP_RCV is set). Receive frames
which have a length field of 46 bytes or greater will be
passed to the host unmodified.
Since any valid Ethernet Type field value will always be
greater than a normal 802.3 Length field (
≥
46), the PC-
net-ISA II controller will not attempt to strip valid Ether-
net frames.
Note that for some network protocols the value passed
in the Ethernet Type and/or 802.3 Length field is not
compliant with either standard and may cause problems.
The diagram below shows the byte/bit ordering of the
received length field for an 802.3 compatible frame
format.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C961AVCW | PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
| AM79C961AVIW | PCnet⑩-ISA II Jumperless, Full Duplex Single-Chip Ethernet Controller for ISA |
| Am79C965A | PCnet?-32 Single-Chip 32-Bit Ethernet Controller |
| AM79C970AKCW | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
| AM79C970AKC | PCnet-PCI II Single-Chip Full-Duplex Ethernet Controller for PCI Local Bus Product |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C961APDLUTS | 制造商:Advanced Micro Devices 功能描述: |
| AM79C961AVC | 制造商:Rochester Electronics LLC 功能描述: 制造商:Advanced Micro Devices 功能描述:LAN Node Controller, 144 Pin, TQFP |
| AM79C961AVC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller |
| AM79C961AVC\\W | 制造商:Rochester Electronics LLC 功能描述: |
| AM79C961AVC\W | 制造商:Rochester Electronics LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。