- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C975 (Advanced Micro Devices, Inc.) PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY PDF資料下載
參數資料
| 型號： | AM79C975 |
| 廠商： | Advanced Micro Devices, Inc. |
| 英文描述： | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| 中文描述： | PCnet⑩快速三單芯片10/100 Mbps的PCI以太網控制器集成PHY |
| 文件頁數： | 252/304頁 |
| 文件大?。?/td> | 2092K |
| 代理商： | AM79C975 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁當前第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁第285頁第286頁第287頁第288頁第289頁第290頁第291頁第292頁第293頁第294頁第295頁第296頁第297頁第298頁第299頁第300頁第301頁第302頁第303頁第304頁
252
Am79C973/Am79C975
P R E L I M I N A R Y
network. Any value above 128 will create unpredictable
results. Padding is not supported by the SMIU.
Once the Transmit Data memory is filled with the data
of the alert frame and the Transmit Message Length
register is setup with the length of the alert frame, the
host must set the MTX_START bit in the Transmit Sta-
tus register to start the transmission. The Am79C975
controller will transmit the alert frame after any pending
frame transmission (including retries) has completed.
The host can poll the MTX_DONE bit in the Interrupt
register to determine if the transmission of the alert
frame has already ended. The MTX_DONE bit will be
set to a 1 after the end of transmission, independent of
the success of the operation. The MTX_DONE bit will
auto-clear after reading the Interrupt register.
The MTX_ADR register is cleared by setting the
MTX_START bit. The host must not load data for a new
alert frame into the Transmit Data memory until the
transmission of the current frame is ended as indicated
by the MTX_DONE bit. It is possible to issue a new
MTX_START command without loading new data to
the Transmit Data memory or updating the MTX_LEN
register.
The Am79C975 controller provides an asynchronous
interrupt pin to signal the host that the transmission of
the alert frame is complete. After the end of the trans-
mission, the MIRQ pin will be asserted, if the global in-
terrupt enable bit MIRQEN in the Command register is
set to a 1 and the transmit interrupt mask bit
(MTX_DONEM) is cleared to 0 (default state). Once
MIRQ is asserted, the host can read the MTX_DONE
bit in the Interrupt register to determine that the inter-
rupt was caused by the end of the transmission. The
read of the Interrupt register will clear the MTX_DONE
bit and cause the deassertion of the MIRQ pin. The In-
terrupt register also provides a global interrupt bit
MIRQ that is the OR of the MTX_DONE and
MRX_DONE bits.
Once the MTX_DONE bit indicates that the transmis-
sion of the alert frame has ended, MTX_START is
cleared and the SMIU Transmit Status register provides
the error status for the transmission. Three error condi-
tions are reported: Late Collision, Loss of Carrier and
Retry Error. There is also an error summary bit
(MTX_ERR). The transmit status bits remain valid as
long as the MTX_START bit is set to 0.
The Transmit Retry Error condition requires special at-
tention. It can happen, that the START or STOP bit is
set in the Am79C975 controller to change normal oper-
ation. START and STOP cause a reset of the transmit
logic. Normal transmission of an alert frame will suc-
ceed. If, however, the SMIU is in the middle of a backoff
interval or the transmission of the alert frame is suffer-
ing a collision, the transmission will abort and the
MTX_RTRY bit will be set. If MTX_RTRY is set in the
SMIU Transmit Status register, the host should re-
transmit the frame.
Receive Operation
The System Management Interface Unit (SMIU) of the
Am79C975 controller provides a separate 128-byte
Receive Data memory to store an incoming manage-
ment or acknowledgment frame. The normal receive
address matching mechanism (physical address, logi-
cal address, broadcast address) of the MAC cannot be
used by the SMIU. The Am79C975 controller provides
an Acknowledgment Frame Filter instead. The filter is
stored in a 40-byte Receive Pattern RAM.
The Receive Pattern RAM is organized as 8 pattern
words of 5 bytes each. Each pattern word holds four
bytes of data to be compared with the incoming frame
plus mask information that indicates which bytes
should be included in the comparison. The pattern
word also contains a field that indicates how many
Dwords of the incoming frame should be skipped be-
fore this Dword of pattern is compared with frame data.
This field makes it unnecessary to store data for long
series of bytes that will be excluded from the compari-
son anyway. A maximum of 7 Dwords (28 bytes) can be
skipped. If the filter pattern contains a string of more
than 7 Dwords that must be excluded from the compar-
ison, one or more pattern words will be loaded with the
value 7h in the Skip field and 0h in the Mask field. Fi-
nally the most significant bit of the pattern word indi-
cates whether or not this word is the end of the stored
pattern.
The format of the pattern words is shown below.
Bits
Name
Description
31:0
Pattern
Bytes of data to be compared with the incoming frame. The least significant byte corresponds to the
first byte of the Dword received from the network.
35:32
Mask
Bits 3:0 of this field correspond to bytes 3:0 of the pattern field. If bit n of this field is 0, byte n of the
pattern is ignored in the comparison.
38:36
Skip
This field indicates how many Dwords of the incoming frame must be skipped before the pattern in this
word is compared with data from the incoming frame. A maximum of 7 Dwords may be skipped per
pattern word.
39
EOP
End of Pattern. If this bit is set, this pattern word contains the last Dword of the frame filter.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C973 | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C973KCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C975KCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C973VCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C975VCW | PCnet⑩-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C975BKC\\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C975BKC\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C975BKD\\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C975BKD\W | 制造商:Advanced Micro Devices 功能描述:PCnet-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY 制造商:AMD (Advanced Micro Devices) 功能描述:PCnet-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
| AM79C975BKDW | 制造商:Advanced Micro Devices 功能描述:PCnet-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY 制造商:AMD (Advanced Micro Devices) 功能描述:PCnet-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY |
發布緊急采購，3分鐘左右您將得到回復。