參數資料
型號： CP2201EK
廠商： Silicon Laboratories Inc
文件頁數： 19/108頁
文件大?。?/td> 0K
描述： KIT EVAL FOR CP2201 ETH CTRLR
標準包裝： 1
主要目的： 接口，以太網傳感器
嵌入式： 是，MCU，8 位
已用 IC / 零件： CP2200，CP2201
主要屬性： 溫度和光傳感器
次要屬性： 圖形用戶界面
已供物品： 板，電源，線纜，CD
產品目錄頁面： 627 (CN2011-ZH PDF)
相關產品： 336-1313-ND - IC ETH CTRLR SNGL-CHIP 28QFN
336-1312-ND - IC ETH CTRLR SNGL-CHIP 48TQFP
其它名稱： 336-1316
CP2200/1
18
Rev. 1.0
6. Functional Description
6.1. Overview
In most systems, the CP2200/1 is used for transmitting and receiving Ethernet packets, non-volatile data storage,
and controlling Link and Activity LEDs. The device is controlled using direct and indirect internal registers
accessible through the parallel host interface. All digital pins on the device are 5 V tolerant.
6.2. Reset Initialization
After every CP2200/1 reset, the following initialization procedure is recommended to ensure proper device
operation:
Step 1: Wait for the reset pin to rise. This step takes the longest during a power-on reset.
Step 2: Wait for Oscillator Initialization to complete. The host processor will receive notification through the
interrupt request signal once the oscillator has stabilized.
Step 3: Wait for Self Initialization to complete. The INT0 interrupt status register on page 31 should be
checked to determine when Self Initialization completes.
Step 4: Disable interrupts (using INT0EN and INT1EN on page 33 and page 36) for events that will not be
monitored or handled by the host processor. By default, all interrupts are enabled after every reset.
Step 5: Initialize the physical layer. See “15.7. Initializing the Physical Layer” on page 90 for a detailed
physical layer initialization procedure.
Step 6: Enable the desired Activity, Link, or Activity/Link LEDs using the IOPWR register on page 45.
Step 7: Initialize the media access controller (MAC). See “14.1. Initializing the MAC” on page 78 for a
detailed MAC initialization procedure.
page 59 for a detailed initialization procedure.
Step 9: The CP2200/1 is ready to transmit and receive packets.
6.3. Interrupt Request Signal
The CP2200/1 has an interrupt request signal (INT) that can be used to notify the host processor of pending
interrupts. The INT signal is asserted upon detection of any enabled interrupt event. Host processors that cannot
dedicate a port pin to the INT signal can periodically poll the interrupt status registers to see if any interrupt
generating events have occurred. If the /INT signal is not used, pending interrupts such a Receive FIFO Full must
still be serviced.
The 14 interrupt sources are listed below. Interrupts are enabled on reset and can be disabled by software.
Pending interrupts can be cleared (allowing the INT signal to de-assert) by reading the self-clearing interrupt
registers. See “8. Interrupt Sources” on page 30 for a complete description of the CP2200/1 interrupts.
End of Packet Reached
Packet Received
Receive FIFO Empty
“Wake-on-LAN” Wakeup Event
Receive FIFO Full
Link Status Changed
Oscillator Initialization Complete
Jabber Detected
Self Initialization Complete
Auto-Negotiation Failed
Flash Write/Erase Complete
Remote Fault Notification
Packet Transmitted
Auto-Negotiation Complete
相關PDF資料
PDF描述
PM1210-820J-RC INDUCTOR 82UH 5% 1210 SMD
H3WWH-6036G IDC CABLE - HPL60H/AE60G/HPL60H
UPS2C471MRD CAP ALUM 470UF 160V 20% RADIAL
A3CKB-4006M IDC CABLE - AKC40B/AE40M/APK40B
MODEMDK KIT DEV EMBEDDED MODEM
相關代理商/技術參數
參數描述
CP2201-GM 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
CP2201-GMR 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
CP-220-K 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Coils and Chokes for general use
CP221 制造商:CENTRAL 制造商全稱:Central Semiconductor Corp 功能描述:Small Signal Transistor
CP-221 1 1/2"BL 100' 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3m 系列:CP-221 零件狀態:過期 類型:套管，彈性 收縮率:2 至 1 長度:100'（30.48m） 內徑（出廠）:1.500"（38.1mm） 內徑 - 恢復后:0.752"（19.1mm） 恢復后的壁厚:0.040"（1.02mm） 材料:聚烯烴（PO） 特性:自熄滅 顏色:黑 工作溫度:-55°C ~ 135°C 收縮溫度:121°C 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*