- 您現在的位置：買賣IC網 > PDF目錄16215 > CP2201EK (Silicon Laboratories Inc)KIT EVAL FOR CP2201 ETH CTRLR PDF資料下載
參數資料
| 型號： | CP2201EK |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 97/108頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVAL FOR CP2201 ETH CTRLR |
| 標準包裝： | 1 |
| 主要目的： | 接口，以太網傳感器 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | CP2200，CP2201 |
| 主要屬性： | 溫度和光傳感器 |
| 次要屬性： | 圖形用戶界面 |
| 已供物品： | 板，電源，線纜，CD |
| 產品目錄頁面： | 627 (CN2011-ZH PDF) |
| 相關產品： | 336-1313-ND - IC ETH CTRLR SNGL-CHIP 28QFN 336-1312-ND - IC ETH CTRLR SNGL-CHIP 48TQFP |
| 其它名稱： | 336-1316 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁當前第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
CP2200/1
Rev. 1.0
89
15.3. Loopback Mode
Loopback Mode provides the ability to transfer data from the physical layer’s output directly to it’s input to aid in
system debugging. When PHYCN.3 is set to ‘1’, transmit data is looped back to the receiver via an internal analog
path. The transmit drivers and receive input circuitry are bypassed, isolating the device from the network. This
prevents network traffic from affecting the result of any system self-tests and guarantees a collision-free
environment.
15.4. Link Integrity Function
The Link Integrity function provides the ability to detect and respond to a 10 BASE-T link failure. When such a
failure is detected, the transmitter and receiver are automatically disabled, and the state of the link is reported in
LINKSTA (PHYCN.0). The host can disable the link integrity function by clearing LINKINT (PHYCF.6) to ‘0’. When
the link integrity function is disabled, the physical layer will operate regardless of the presence of link pulses.
15.5. Receiver Smart Squelch and Automatic Polarity Correction
The physical layer receiver can detect and correct for noise or incorrect polarity of the received signal. If the
receiver Smart Squelch feature is enabled by setting SMSQ (PHYCF.7) to ‘1’, the receiver circuitry performs a
combination of amplitude and timing measurements (in accordance with IEEE 802.3) to determine the validity of
received data. This prevents noise from falsely triggering the receiver in the absence of valid data.
Automatic polarity correction can automatically detect and correct the polarity of the received data to compensate
for a wiring error at either end of the 10 BASE-T cable. When automatic polarity correction is enabled by setting
AUTOPOL (PHYCF.1) to ‘1’, the polarity of the receive data is indicated in POLREV (PHYCN.1). When automatic
polarity detection is disabled, the polarity of the receive data can be manually reversed by setting REVPOL
(PHYCF.0) to ‘1’.
15.6. Transmitter Jabber Function
Provides the ability to automatically disable the transmitter if software attempts to transmit a packet longer than the
maximum allowed packet length (per IEEE 802.3). The host processor will be notified via the Jabber Detected
Interrupt if a jabber condition is automatically handled by the hardware. Enabling the jabber function is
recommended to ensure that the embedded system using the CP2200/1 for Ethernet communication does not
generate a jabber condition on the wire.
相關PDF資料 |
PDF描述 |
|---|---|
| PM1210-820J-RC | INDUCTOR 82UH 5% 1210 SMD |
| H3WWH-6036G | IDC CABLE - HPL60H/AE60G/HPL60H |
| UPS2C471MRD | CAP ALUM 470UF 160V 20% RADIAL |
| A3CKB-4006M | IDC CABLE - AKC40B/AE40M/APK40B |
| MODEMDK | KIT DEV EMBEDDED MODEM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP2201-GM | 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| CP2201-GMR | 功能描述:以太網 IC Ethernet Controller RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| CP-220-K | 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Coils and Chokes for general use |
| CP221 | 制造商:CENTRAL 制造商全稱:Central Semiconductor Corp 功能描述:Small Signal Transistor |
| CP-221 1 1/2"BL 100' | 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3m 系列:CP-221 零件狀態:過期 類型:套管，彈性 收縮率:2 至 1 長度:100'（30.48m） 內徑（出廠）:1.500"（38.1mm） 內徑 - 恢復后:0.752"（19.1mm） 恢復后的壁厚:0.040"（1.02mm） 材料:聚烯烴（PO） 特性:自熄滅 顏色:黑 工作溫度:-55°C ~ 135°C 收縮溫度:121°C 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。