- 您現在的位置：買賣IC網 > PDF目錄366891 > CR16HCS9VJE8Y Microcontroller PDF資料下載
參數資料
| 型號： | CR16HCS9VJE8Y |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 83/157頁 |
| 文件大?。?/td> | 1256K |
| 代理商： | CR16HCS9VJE8Y |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁當前第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
83
www.national.com
until cleared by a STOP condition or a one is
written to it.
Address Match. In slave mode, MATCH is set
when ACBADDR.SAEN is set and the first sev-
en bits of the address byte (the first byte trans-
ferred after a Start Condition) matches the 7-bit
address in the ACBADDR register. It is cleared
by Start Condition, repeated start and Stop
Condition (including illegal Start or Stop Condi-
tion).
Global Call Match bit. In slave mode, GCMTCH
is set when ACBCTL1.GCMEN is set and the
address byte (the first byte transferred after a
Start Condition) is 00
16
. It is cleared by Start
Condition, repeated Start and Stop Condition
(including illegal Start or Stop Condition).
Test SDA Line. Reads the current value of the
SDA line. This bit can be used while recovering
from an error condition in which the SDA line is
constantly pulled low by a slave that went out
of synch. This bit is a read-only bit. Data written
to it is ignored.
Toggle SCL Line. This bit enables toggling the
SCL line during the process of error recovery.
When the SDA line is low, writing 1 to this bit
toggles the SCL line for one cycle. Writing 1 to
TGSCL when SDA is high is ignored. The bit is
cleared when the clock toggle is completed.
MATCH
GCMTCH
TSDA
TGSCL
19.3.4
ACB Control 1 Register (ACBCTL1) is a byte-wide, read/
write register that configures and controls the ACB module.
Upon reset and while the module is disabled (ACBCTL2.EN-
ABLE=0), the ACBCTL1 is cleared (00
16
).
7
6
5
4
STAS-
TRE
ACB Control 1 Register (ACBCTL1)
START
START. This bit is set when a Start Condition
needs to be generated on the ACCESS.bus.
The START bit is cleared when the Start Con-
dition is sent, or upon detection of a Bus Error
(ACBST.BER=1). This bit should be set only
when in Master mode, or when requesting
Master mode.
If this device is not the active master of the bus
(ACBST.MASTER=0), setting START gener-
ates a Start Condition as soon as the
ACCESS.bus is free (ACBCST.BB=0). An ad-
dress send sequence should then be per-
formed.
If this device is the active master of the bus
(ACBST.MASTER=1), when START is set, a
write to the ACBSDA register generates a Start
Condition, then the ACBSDA data is transmit-
ted as the slave’s address and the requested
transfer direction.
This case is a repeated Start Condition. It may
be used to switch the direction of the data flow
between the master and the slave, or to choose
another slave device without using a Stop Con-
dition in between.
STOP
STOP. In master mode, setting this bit gener-
ates a Stop Condition that completes or aborts
the current message transfer. This bit clears it-
self after the STOP is issued.
Interrupt Enable. When INTEN is cleared ACB
interrupt is disabled. When INTEN is set, inter-
rupts are enabled. An interrupt is generated
(the interrupt signals to the ICU is high) upon
one of the following events:
An address MATCH is detected (ACB-
ST.NMATCH=1) and NMINTE is set.
A Bus Error occurs (ACBST.BERR=1).
Negative acknowledge after sending a byte
(ACBST.NEGACK=1).
An interrupt is generated upon acknowl-
edge of each transaction (same as the
hardware set of the ACBST.SDAST bit).
In master mode if ACBCTL1.STASTRE=1,
after a successful start (ACBST.STAS-
TR=1).
Detection of a Stop Condition while in slave
receive mode (ACBST.SLVSTP=1).
Acknowledge bit. When acting as a receiver
(slave or master), this bit holds the value this
device sends during the next acknowledge cy-
cle. Setting this bit to 1 instructs the transmit-
ting device to stop sending data, since the
receiver either does not need, or cannot re-
ceive, any more data. This bit is cleared after
the first acknowledge cycle.
This bit is ignored when in transmit mode.
Global Call Match enable. When this bit is set,
it enables the match of an incoming address
byte to the general call address (Start Condi-
tion followed by address byte of 00
16
) while the
ACB is in slave mode. When cleared, the ACB
does not respond to a global call.
New Match Interrupt Enable. Set NMINTE to
enable the interrupt on a new match (i.e., when
ACBST.NMATCH is set). The interrupt is is-
sued only if ACBCTL1.INTEN is set.
Stall After Start Enable. When set enables the
stall after start mechanism. In such a case, the
ACB is stalled after the address byte. When
STASTRE is cleared, ACBST.STASTR is al-
ways cleared.
INTEN
ACK
GCMEN
NMINTE
STASTRE
19.3.5
The ACB Control 2 register (ACBCTL2) is a byte-wide, read/
write register that enables/disables the module and deter-
mines ACB clock rate. Upon reset ACBCTL2 is set to 00
16
.
7
SCLFRQ
ACB Control 2 Register (ACBCTL2)
ENABLE
Enable. When this bit is set, the ACB module is
enabled. When the Enable bit is cleared, the
ACB module is disabled, ACBCTL1, ACBST
and ACBCST are cleared, and the clocks are
halted.
SCL Frequency. This field defines the SCL’s
period (low time and high time) when this de-
SCLFRQ
3
2
1
0
NMINTE
GCMEN ACK Reserved INTEN
STOP
START
1
0
ENABLE
相關PDF資料 |
PDF描述 |
|---|---|
| CR16HCT5 | |
| CR16HCT5VJE7Y | Microcontroller |
| CR16HCT5VJE8Y | Microcontroller |
| CR16HCT5VJE9Y | Microcontroller |
| CR16HCT9 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16HCS9VJE9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers |
| CR16HCS9VJI0 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers |
| CR16HCS9VJI1 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers |
| CR16HCS9VJI2 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers |
| CR16HCS9VJI3 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。