- 您現在的位置：買賣IC網 > PDF目錄366891 > CR16HCT5 PDF資料下載
參數資料
| 型號： | CR16HCT5 |
| 文件頁數： | 12/157頁 |
| 文件大小： | 1256K |
| 代理商： | CR16HCT5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
www.national.com
12
5.0
System Configuration
The device has two input pins, ENV0 and ENV1, which are
used to specify the operating environment of the device upon
reset. There are also two system configuration registers,
called the Module Configuration (MCFG) register and the
Module Status (MSTAT) register.
5.1
Upon reset, the operating mode of the device is determined
by the state of the ENV0 and ENV1 input pins, as indicated
in Table 6.
Table 6
Operating Environment Selection
ENV0 AND ENV1 PINS
In the case where the ENV1 and ENV0 pins are both high,
the reset algorithm looks at the FLCTRL2.EMPTY bit to de-
termine whether the program memory is empty, and sets the
operating mode accordingly.
The ENV0 and ENV1 pins have on-chip pull-up devices that
are enabled during reset while the pins are being sampled.
Therefore, if they are left unconnected, the inputs are consid-
ered high and the normal operating mode (IRE-Mode) is se-
lected and the CPU starts to execute code at address 0. To
enter any other operating mode, the external hardware must
drive the appropriate input low.
In the case where the ISP-Mode is selected, the chip starts
executing the ISP code residing in the on-chip ISP-Memory
area.
The test modes are Reserved for factory testing and for ex-
ternal programming of the flash EEPROM program memory.
They should not be invoked otherwise.
5.2
MODULE CONFIGURATION (MCFG)
REGISTER
The MCFG register is a byte-wide, read/write register that
sets the clock output features of the device.
Upon reset, the non-reserved bits of this register are cleared
to zero. The start-up software must write a specific value to
this register in order to configure the CLK output pin function.
When the software writes to this register, it must write a zero
to each reserved bit for the device to operate properly. The
register should be written in active mode only, not in power
save, HALT, or IDLE mode. However, the register contents
are preserved during all power modes.
The MCFG register format is shown below.
CLKOE
CPU Clock Output Enable. When this bit is
cleared (0), the CLK pin (ENV1) remains in the
high-impedance state. When this bit is set (1) in
normal operating mode, the CLK pin operates
as a CPU clock output.
Generated Clock Output 1 Enable. When
cleared (0), the CLKOUT1 pin (ENV0) stays in
high impedance state. When set (1), the pin
outputs the clock from the prescaler controlled
by PRSSC1.SCDIV1.
Generated Clock Output 2 Enable. When this
bit is set (1) and CLKOE is cleared, the
CLKOUT2 pin (ENV1) outputs the clock from
the prescaler controlled by PRSSC1.SCDIV2.
Otherwise, the CLKOUT2 pin is in high imped-
ance state.
CLK1OE
CLK2OE
5.3
The MSTAT register is a byte-wide, read-only register that in-
dicates the general status of the device.
The MCFG register format is shown below.
7
4
3
Reserved
PGMBUSY
Reserved
MODULE STATUS (MSTAT) REGISTER
OENV(1:0)
Operating Environment. These two bits contain
the values applied to the ENV1 and ENV0 pins
upon reset. These bit values are controlled by
the external hardware upon reset and are held
constant in the register until the next reset.
Flash EEPROM Programming Busy. This bit is
automatically set to 1 when either the program
memory or the data memory is busy being pro-
grammed or erased. It is cleared to 0 when nei-
ther of the two flash EEPROM memories is
busy being programmed or erased. When this
bit is set, the software should not attempt any
write access to either of these two memories.
PGMBUSY
ENV1
ENV0
Operating Environment
0
0
1
0
1
0
Test Mode Flash Me3mory
Test Mode
In-System-Programming mode (ISP)
Internal ROM enabled Mode (IRE), if
program memory is not empty; or ISP-
Mode, if program memory is empty
1
1
7
6
5
4
3
2
1
0
Reserved CLK2OE
Reserved
CLK1OE
CLKOE
Reserved
2
1
0
OENV1
OENV0
相關PDF資料 |
PDF描述 |
|---|---|
| CR16HCT5VJE7Y | Microcontroller |
| CR16HCT5VJE8Y | Microcontroller |
| CR16HCT5VJE9Y | Microcontroller |
| CR16HCT9 | |
| CR16HCT9VJE7 | Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16HCT5VJE7Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT5VJE8Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT5VJE9Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT5VJEXY | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
| CR16HCT9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。