- 您現在的位置：買賣IC網 > PDF目錄376727 > DK2100 (Electronic Theatre Controls, Inc.) Navigator Motion Processor PDF資料下載
參數資料
| 型號： | DK2100 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Navigator Motion Processor |
| 中文描述： | 導航運動處理器 |
| 文件頁數： | 36/59頁 |
| 文件大?。?/td> | 1925K |
| 代理商： | DK2100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
MC2300 Technical Specifications
36
CP chip
Pin Name and
number
PosLim3/
Synch
Direction
Description
54
input/output
On the MC2340 chipset, this pin is the positive-side (forward) travel limit switch
for axis#3. On the MC2320 and MC2310 chipsets this pin is not used.
On the MC23x3 chipset, this pin is the synchronization signal. In the disabled
mode, the pin is configured as an input and is not used. In the master mode, the
pin outputs a synchronization pulse that can be used by slave nodes or other
devices to synchronize with the internal chip cycle of the master node. In the
slave mode, the pin is configured as an input and a pulse on the pin synchronizes
the internal chip cycle.
WARNING! If a valid axis limit pin is not used, its signal should
be tied high.
NC/PosLim3
45
input
On the MC23x0 chipset, this pin is not used.
On the MC2343 chipset, this pin is the positive-side (forward) travel limit switch
for axis#3. On the MC2323 and MC2313 chipsets this pin is not used.
WARNING! If a valid axis limit pin is not used, its signal should
be tied high.
NegLim1
NegLim2
NegLim3
NegLim4
64
66
55
51
input
These signals provide inputs from the negative-side (reverse) travel limit
switches. On power-up or
Reset
these signals default to active
low
interpretation,
but the interpretation can be set explicitly using the
SetSignalSense
instruction.
For MC2340 all 4 pins are valid. For MC2320 only
NegLim1
and
NegLim2
are
valid. For MC2310 only
NegLim1
is valid.
WARNING! If a valid axis pin is not used, its signal must be tied
high. NegLim1 is an output during device reset and as such any
connection to GND or V
cc
must be via a series resistor.
Invalid axis pins may also be left unconnected.
Each of these pins can be conditioned to track the state of any bit in the Status
registers associated with its axis.
For MC2340 all 4 pins are valid. For MC2320 only
AxisOut1
and
AxisOut2
are
valid. For MC2310 only
AxisOut1
is valid.
Invalid or unused pins may be left unconnected.
These are general-purpose programmable inputs. They may be used as a
breakpoint input, to stop a motion axis, or to cause an UPDATE to occur.
For MC2340 all 4 pins are valid. For MC2320 only
AxisIn1
and
AxisIn2
are valid.
For MC2310 only
AxisIn1
is valid.
Invalid or unused pins may be left unconnected.
Hall sensor inputs. Each set (A, B, and C) of signals encodes 6 valid states as
follows: A on, A and B on, B on, B and C on, C on, C and A on. A sensor is
defined as being on when its signal is
high
.
Note: These signals should only be connected to Hall sensors that are mounted
at a 120° offset. Schemes which provide Hall signals 60° apart will not work.
For MC2340 all 12 pins are valid. For MC2320 only the first six pins (axes 1 and
2) are valid. For MC2310 only the first three pins (axis 1) are valid.
Invalid or unused pins may be left unconnected.
AxisOut1
AxisOut2
AxisOut3
AxisOut4
94
95
96
97
output
AxisIn1
AxisIn2
AxisIn3
AxisIn4
72
100
106
67
input
Hall1A
Hall1B
Hall1C
Hall2A
Hall2B
Hall2C
Hall3A
Hall3B
Hall3C
Hall4A
Hall4B
Hall4C
73
90
91
101
102
105
107
108
109
68
69
70
Input
相關PDF資料 |
PDF描述 |
|---|---|
| DK3300 | Turbo uPSD DK3300 User Manual(Turbo系列 uPSD DK3300 用戶手冊) |
| DK60 | DIODY PROSTOWNICZE |
| DK61 | DIODY PROSTOWNICZE |
| DK62 | DIODY PROSTOWNICZE |
| DK63 | DIODY PROSTOWNICZE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DK-2112 | 制造商:Pro'skit 功能描述:Auto Loading Utility Knife |
| DK-21169 | 制造商:SLPOWER 制造商全稱:SL Power Electronics 功能描述:IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME |
| DK-21192 | 制造商:SLPOWER 制造商全稱:SL Power Electronics 功能描述:IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME |
| DK2205 | 制造商:BROTHER MOBILE SOLUTIONS INC. 功能描述:Labels, Adhesive, Overall Length 100', Overall Width 2-2/5 In., Black/White, Pap |
| DK22113 | 制造商:Brother 功能描述:TAPE CONTINUOUS CLEAR FILM 62MM 制造商:BROTHER 功能描述:62MM FILM ROLL, CLEAR |
發布緊急采購，3分鐘左右您將得到回復。