參數資料
型號： DP83848C-MAU-EK
廠商： National Semiconductor
文件頁數： 6/86頁
文件大小： 0K
描述： BOARD EVALUATION DP83848C
標準包裝： 1
主要目的： 接口，以太網
已用 IC / 零件： DP83848C
已供物品： 板
相關產品： DP83848CVVX/NOPBTR-ND - TXRX ETHERNET PHYTER 48-LQFP
DP83848CVV-ND - IC TXRX ETHERNET PHYTER 48-LQFP
13
www.national.com
DP
83
84
8
C
AN_EN (LED_ACT/COL)
AN_1 (LED_SPEED)
AN_0 (LED_LINK)
S, O, PU
26
27
28
Auto-Negotiation Enable: When high, this enables Auto-Negoti-
ation with the capability set by ANO and AN1 pins. When low, this
puts the part into Forced Mode with the capability set by AN0 and
AN1 pins.
AN0 / AN1: These input pins control the forced or advertised op-
erating mode of the DP83848C according to the following table.
The value on these pins is set by connecting the input pins to
GND (0) or VCC (1) through 2.2 k resistors. These pins should
NEVER be connected directly to GND or VCC.
The value set at this input is latched into the DP83848C at Hard-
ware-Reset.
The float/pull-down status of these pins are latched into the Basic
Mode Control Register and the Auto_Negotiation Advertisement
Register during Hardware-Reset.
The default is 111 since these pins have internal pull-ups.
MII_MODE (RX_DV)
SNI_MODE (TXD_3)
S, O, PD
39
6
MII MODE SELECT: This strapping option pair determines the
operating mode of the MAC Data Interface. Default operation (No
pull-ups) will enable normal MII Mode of operation. Strapping
MII_MODE high will cause the device to be in RMII or SNI mode
of operation, determined by the status of the SNI_MODE strap.
Since the pins include internal pull-downs, the default values are
0.
The following table details the configurations:
LED_CFG (CRS)
S, O, PU
40
LED CONFIGURATION: This strapping option determines the
mode of operation of the LED pins. Default is Mode 1. Mode 1 and
Mode 2 can be controlled via the strap option. All modes are con-
figurable via register access.
SeeTable 3 for LED Mode Selection.
MDIX_EN (RX_ER)
S, O, PU
41
MDIX ENABLE: Default is to enable MDIX. This strapping option
disables Auto-MDIX. An external pull-down will disable Auto-
MDIX mode.
Signal Name
Type
Pin #
Description
AN_EN AN1
AN0
Forced Mode
0
10BASE-T, Half-Duplex
0
1
10BASE-T, Full-Duplex
0
1
0
100BASE-TX, Half-Duplex
0
1
100BASE-TX, Full-Duplex
AN_EN AN1
AN0
Advertised Mode
1
0
10BASE-T, Half/Full-Duplex
1
0
1
100BASE-TX, Half/Full-Duplex
1
0
10BASE-T Half-Duplex
100BASE-TX, Half-Duplex
1
10BASE-T, Half/Full-Duplex
100BASE-TX,Half/Full-Duplex
MII_MODE SNI_MODE
MAC Interface
Mode
0
X
MII Mode
1
0
RMII Mode
1
10 Mb SNI Mode
相關PDF資料
PDF描述
2-5492591-0 CA 50/125UMRIS SCDUP/2.5BAY 20M1
6278899-1 CA,62.5,MTRJ-SC
L-07W18NKV4T WIREWOUND INDUCTOR 18NH 0402
ECM24DRSN CONN EDGECARD 48POS DIP .156 SLD
1-6828318-2 C/A,2.0MM,RISER,XG,AQUA,LC-SC
相關代理商/技術參數
參數描述
DP83848C-POE-EK 功能描述:以太網開發工具 DP83848 POE CARD COMM TEMP RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
DP83848CVV 制造商:Texas Instruments 功能描述:IC, 10/100 ETHERNET PHY, SMD, LQFP48
DP83848CVV/NOPB 功能描述:以太網 IC PHYTER COMMERCIAL TEMP SGL PORT RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
DP83848CVV/NOPB 制造商:Texas Instruments 功能描述:Ethernet Transceiver
DP83848CVVX 制造商:Texas Instruments 功能描述:PHY 1-CH 10Mbps/100Mbps 48-Pin LQFP T/R
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*