參數資料
型號： DS1865K
廠商： Maxim Integrated Products
文件頁數： 44/67頁
文件大?。?/td> 0K
描述： KIT EVAL FOR DS1865
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
主要目的： 電信，無源光學網絡（PON）
已用 IC / 零件： DS1865
DS1865
PON Triplexer Control and
Monitoring Circuit
____________________________________________________________________
49
Table 02h, Register 89h: Config
FACTORY DEFAULT
00h
READ ACCESS
PW2
WRITE ACCESS
PW2
MEMORY TYPE:
Nonvolatile (SEE)
89h
FETG DIR
TX-F EN
RESERVED
ASEL
RESERVED
bit7
bit0
Configure the memory location and the polarity of the digital outputs.
bit7
FETG DIR: Chooses the direction or polarity of the FETG output for normal operation.
0 = (Default) Under normal operation, FETG is pulled low. Intended for use with nMOS.
1 = Under normal operation, FETG is pulled high. Intended for use with pMOS.
bit6
TX-F EN: The TX-F output pin always reflects the wired-OR of all TXF enabled alarm states. This bit
will enable the latching of the alarm state for the TXF output pin.
0 = (Default) Not latched.
1 = The alarm bits are latched until cleared by a TX-D transition or power-down. If VCC_Lo_Alarm is
enabled for either FETG or TX-F then latching is disabled until the after the first VCC measurement is
made above the VCC_Lo set point to allow for proper operation during slow power-on cycles.
bit5
RESERVED
bit4
ASEL: Address Select.
0 = (Default) Device Address of A2h.
1 = I2C slave address is determined by the value programmed in the DEVICE ADDRESS byte
(Table 02h, Register 8Ch).
bit3:0
RESERVED
Table 02h, Register 8Ah: Startup Step
FACTORY DEFAULT:
00h
READ ACCESS
PW2
WRITE ACCESS
PW2
MEMORY TYPE:
Nonvolatile (SEE)
8Ah
2
12
2
11
2
10
2
9
2
8
2
7
2
6
2
5
bit7
bit0
This value will define the maximum allowed step for the upper 8 bits of IBIAS output during startup. Programming this value to 00h
cause the device to take single LSB (2
0) steps towards convergence. See the BIAS and MOD Output During Power-Up section for
details.
相關PDF資料
PDF描述
EBM24DRKF CONN EDGECARD 48POS DIP .156 SLD
M1GXK-3436R IDC CABLE - MCS34K/MC34M/X
HSM06DRKH CONN EDGECARD 12POS DIP .156 SLD
380LX681M400A052 CAP ALUM 680UF 400V 20% SNAP
EBM25DREI CONN EDGECARD 50POS .156 EYELET
相關代理商/技術參數
參數描述
DS1865T TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit
DS1865T+ 功能描述:電流和電力監控器、調節器 PON Triplexer Cntrl & Monitoring Circuit RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel
DS1865T+T&R 制造商:Maxim Integrated Products 功能描述:TRIPLEXER CONTROL AND MONITORING CIRCUIT 1TX 1RX 1.25GBPS 28 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC PON CONTROL TRI 28-TQFN 制造商:Maxim Integrated Products 功能描述:Current & Power Monitors & Regulators PON Triplexer Cntrl & Monitoring Circuit
DS1865T+T&R 功能描述:電流和電力監控器、調節器 PON Triplexer Cntrl & Monitoring Circuit RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel
DS1865T+TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*