inadequat" />
參數資料
型號： DS1865K
廠商： Maxim Integrated Products
文件頁數： 7/67頁
文件大?。?/td> 0K
描述： KIT EVAL FOR DS1865
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1
主要目的： 電信，無源光學網絡（PON）
已用 IC / 零件： DS1865
DS1865
PON Triplexer Control and
Monitoring Circuit
____________________________________________________________________
15
inadequate VCC exists to operate the laser driver. Once
adequate VCC is present to clear the VCC low alarm, the
outputs are enabled following the same sequence as the
power-up sequence.
As previously mentioned, the FETG is an output used to
disable the laser current through a series nMOSFET or
pMOSFET. This requires that the FETG output can sink
or source current. Because the DS1865 does not know
if it should sink or source current before VCC exceeds
VPOA, which triggers the EE recall, this output will
be high impedance when VCC is below VPOA (see the
Low-Voltage Operation section for details and
diagram). The application circuit must use a pullup or
pulldown resistor on this pin that pulls FETG to the
alarm/shutdown state (high for a pMOS, low for a
nMOS). Once VCC is above VPOA, the DS1865 pulls the
FETG output to the state determined by the FETG DIR
bit (Table 02h, Register 89h). FETG DIR is 0 if an nMOS
is used and 1 if a pMOS is used.
Determining Alarm Causes
Using the I2C Interface
To determine the cause of the TX-F or FETG alarm, the
system processor can read the DS1865’s Alarm Trap
Bytes (ATB) through the I2C interface (in Table 01h). The
ATB has a bit for each alarm. Any time an alarm occurs,
regardless of the mask bit’s state, the DS1865 sets the
corresponding bit in the ATB. Active ATB bits remain set
until written to zeros through the I2C interface. On power-
up, the ATB is zeros until alarms dictate otherwise.
Die Identification
The DS1865 has an ID hard coded to its die. Two regis-
ters (Table 02h bytes 86h–87h) are assigned for this
feature. Byte 86h reads 65h to identify the part as the
DS1865, byte 87h reads the die revision.
Low-Voltage Operation
The DS1865 contains two power-on reset (POR) levels.
The lower level is a digital POR (VPOD) and the higher
level is an analog POR (VPOA). At startup, before the
supply voltage rises above VPOA, the outputs are dis-
abled (FETG and BIAS outputs are high impedance,
MOD is low), all SRAM locations are low (including
shadowed EEPROM), and all analog circuitry is dis-
abled. When VCC reaches VPOA, the SEE is recalled,
and the analog circuitry is enabled. While VCC remains
above VPOA, the device is in its normal operating state,
and it responds based on its nonvolatile configuration.
If during operation VCC falls below VPOA but is still
above VPOD, the SRAM retains the SEE settings from
TX-F LATCHED OPERATION
TX-F NON LATCHED OPERATION
DETECTION OF
TX-F FAULT
TX-D OR
TX-F RESET
TX-F
DETECTION OF
TX-F FAULT
TX-F
Figure 5. TX-F Timing
Table 4. TX-F as a Function of TX-D and
Alarm Sources
VCC > VPOA
TX-D
NONMASKED
TX-F ALARM
TX-F
No
X
1
Yes
0
Yes
0
1
Yes
1
X
0
相關PDF資料
PDF描述
EBM24DRKF CONN EDGECARD 48POS DIP .156 SLD
M1GXK-3436R IDC CABLE - MCS34K/MC34M/X
HSM06DRKH CONN EDGECARD 12POS DIP .156 SLD
380LX681M400A052 CAP ALUM 680UF 400V 20% SNAP
EBM25DREI CONN EDGECARD 50POS .156 EYELET
相關代理商/技術參數
參數描述
DS1865T TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit
DS1865T+ 功能描述:電流和電力監控器、調節器 PON Triplexer Cntrl & Monitoring Circuit RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel
DS1865T+T&R 制造商:Maxim Integrated Products 功能描述:TRIPLEXER CONTROL AND MONITORING CIRCUIT 1TX 1RX 1.25GBPS 28 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC PON CONTROL TRI 28-TQFN 制造商:Maxim Integrated Products 功能描述:Current & Power Monitors & Regulators PON Triplexer Cntrl & Monitoring Circuit
DS1865T+T&R 功能描述:電流和電力監控器、調節器 PON Triplexer Cntrl & Monitoring Circuit RoHS:否 制造商:STMicroelectronics 產品:Current Regulators 電源電壓-最大:48 V 電源電壓-最小:5.5 V 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:HPSO-8 封裝:Reel
DS1865T+TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:PON Triplexer Control and Monitoring Circuit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*