參數資料
型號： DS2196LN
廠商： DALLAS SEMICONDUCTOR
元件分類： Digital Transmission Controller
英文描述： DATACOM, FRAMER, PQFP100
封裝： LQFP-100
文件頁數： 71/160頁
文件大?。?/td> 559K
代理商： DS2196LN
DS2196
18 of 160
PARALLEL CONTROL PORT PINS
Signal Name:
INT*
Signal Description:
Interrupt
Signal Type:
Output
Flags host controller during conditions and change of states as defined in the Status Registers. Active
low, open drain output.
Signal Name:
MUX
Signal Description:
Bus Operation
Signal Type:
Input
Set low to select non-multiplexed bus operation. Set high to select multiplexed bus operation.
Signal Name:
D0 to D7 / AD0 to AD7
Signal Description:
Data Bus or Address/Data Bus
Signal Type:
Input / Output
In non-multiplexed bus operation (MUX = 0), serves as the data bus. In multiplexed bus operation
(MUX = 1), serves as a 8–bit multiplexed address / data bus.
Signal Name:
A0 to A6
Signal Description:
Address Bus
Signal Type:
Input
In non-multiplexed bus operation (MUX = 0), serves as the address bus. In multiplexed bus operation
(MUX = 1), these pins are not used and should be tied low.
Signal Name:
BTS
Signal Description:
Bus Type Select
Signal Type:
Input
Strap high to select Motorola bus timing; strap low to select Intel bus timing. This pin controls the
function of the RD*(DS*), ALE (AS), and WR*(R/W*) pins. If BTS = 1, then these pins assume the
function listed in parenthesis ().
Signal Name:
RD* (DS*)
Signal Description:
Read Input (Data Strobe)
Signal Type:
Input
RD* is an active low signal. DS* polarity is determined by the MUX pin setting. Refer to section 21 for
details.
Signal Name:
CS*
Signal Description:
Chip Select
Signal Type:
Input
Must be low to read or write to the device. CS* is an active low signal.
Signal Name:
ALE(AS) / A7
Signal Description:
A7 or Address Latch Enable (Address Strobe)
Signal Type:
Input
In non-multiplexed bus operation (MUX = 0), serves as the upper address bit.
In multiplexed bus
operation (MUX = 1), serves to demultiplex the bus on a positive–going edge.
相關PDF資料
PDF描述
DS21FF44 DATACOM, FRAMER, PBGA300
DS21FF44N DATACOM, FRAMER, PBGA300
DS21FT40N DATACOM, FRAMER, PBGA300
DS21FT40 DATACOM, FRAMER, PBGA300
DS21FT42 DATACOM, FRAMER, PBGA300
相關代理商/技術參數
參數描述
DS2196LN+ 功能描述:網絡控制器與處理器 IC T1 Dual Framer LIU RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS219T 功能描述:烙鐵 DESOLDERING HEAD RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included
DS21E352 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E352N 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E354 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*