- 您現在的位置：買賣IC網 > PDF目錄1914 > DS21Q59LN+ (Maxim Integrated Products)IC TXRX E1 QUAD 100-LQFP PDF資料下載
參數資料
| 型號： | DS21Q59LN+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 20/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX E1 QUAD 100-LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 90 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 4/4 |
| 規程： | E1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
DS21Q59 Quad E1 Transceiver
27 of 76
9. STATUS AND INFORMATION REGISTERS
The DS21Q59 has a set of four registers that contain information about a framer’s real-time status. The registers
include status register 1 (SR1), status register 2 (SR2), receive information register (RIR), and synchronizer status
register (SSR).
When a particular event has occurred (or is occurring), the appropriate bit in one of these four registers is set to 1.
All the bits in the SR1, SR2, and RIR1 registers operate in a latched fashion. The SSR contents are not latched,
which means that if an event or an alarm occurs and a bit is set to 1 in any of the registers, the bit remains set until
the user reads that bit. The bit is cleared when it is read and is not set again until the event has occurred again (or,
in the case of the RUA1, RRA, RCL, and RLOS alarms, the bit remains set if the alarm is still present).
The user always precedes a read of the SR1, SR2, and RIR registers with a write. The byte written to the register
informs the framer which bits the user wishes to read and have cleared. The user writes a byte to one of these
registers with a 1 in the bit positions he or she wishes to read and a 0 in the bit positions he or she does not wish to
obtain the latest information on. When a 1 is written to a bit location, the read register updates with the latest
information. When a 0 is written to a bit position, the read register does not update and the previous value is held.
A write to the status and information registers is immediately followed by a read of the same register. The read
result should be logically ANDed with the mask byte that was just written, and this value should be written back into
the same register to ensure the bit clears. This second write step is necessary because the alarms and events in
the status registers occur asynchronously in respect to their access through the parallel port. This write-read-write
scheme allows an external microcontroller or microprocessor to individually poll certain bits without disturbing the
other bits in the register. This operation is key in controlling the DS21Q59 with higher-order software languages.
The SSR register operates differently than the other three. It is a read-only register and reports the status of the
synchronizer in real time. This register is not latched and it is not necessary to precede a read of this register with a
write.
The SR1 and SR2 registers have the unique ability to initiate a hardware interrupt through the
INT output pin. Each
of the alarms and events in SR1 and SR2 can be either masked or unmasked from the interrupt pin through
interrupt mask register 1 (IMR1) and interrupt mask register 2 (IMR2).
The interrupts caused by alarms in SR1 (RUA1, RRA, RCL, and RLOS) act differently than the interrupts caused
by events in SR1 and SR2 (RSA1, RDMA, RSA0, RSLIP, RMF, TMF, SEC, TAF, LOTC, and RCMF). The alarm-
caused interrupts force the
INT pin low whenever the alarm changes state (i.e., the alarm goes active or inactive
according to the set/clear criteria in Table 9-A). The
INT pin is allowed to return high (if no other interrupts are
present) when the user reads the alarm bit that caused the interrupt to occur, even if the alarm is still present.
The event-based interrupts force the
INT pin low when the event occurs. The INT pin returns high () when the user
reads the event bit that caused the interrupt to occur. Furthermore, some event-based interrupts occur continuously
as long as the event is occurring (RSLIP, SEC, TMF, RMF, TAF, RAF, RCMF). Other event-based interrupts force
the
INT pin low only once when the event is first detected (LOTC, PRSBD, RDMA, RSA1, RSA0), that is, the
PRBSD interrupt fires once when the receiver detects the PRBS pattern. If the receiver continues to receive the
PRBS pattern, no more interrupts are fired. If the receiver then detects that PRBS is no longer being sent, it resets
and, when it receives the PRBS pattern again, another interrupt is fired.
相關PDF資料 |
PDF描述 |
|---|---|
| DS21S07AS+T&R | IC TERMINATOR SCSI 16-SOIC |
| DS21T05Z/T&R | IC TERMINATOR SCSI 150MIL 16SOIC |
| DS21T07S+T&R | IC TERMINATOR SCSI 16-SOIC |
| DS2250-64-16+ | IC MCU 64KB 16MHZ 40-SIMM |
| DS2251T-128-16 | IC MICROCNTRLR 128K 16MHZ 72SIMM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21Q59LN+ | 功能描述:網絡控制器與處理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21S07A | 制造商:Maxim Integrated Products 功能描述: |
| DS21S07AE | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
| DS21S07AE/T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SCSI Terminator |
| DS21S07AE/T&R | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:IC TERMINATOR SCSI 20-TSSOP |
發布緊急采購，3分鐘左右您將得到回復。