參數資料
型號： DS21Q59LN+
廠商： Maxim Integrated Products
文件頁數： 46/76頁
文件大?。?/td> 0K
描述： IC TXRX E1 QUAD 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 90
類型： 收發器
驅動器/接收器數： 4/4
規程： E1
電源電壓： 4.75 V ~ 5.25 V
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
DS21Q59 Quad E1 Transceiver
50 of 76
Figure 21-3. Transmit Waveform Template
21.3 Jitter Attenuators
The DS21Q59 contains an on-board clock and data jitter attenuator for each transceiver and a single, undedicated
“clock only” jitter attenuator. This undedicated jitter attenuator is shown in the block diagram (Figure 3-1) as the
alternate jitter attenuator.
21.3.1 Clock and Data Jitter Attenuators
The clock and data jitter attenuators can be mapped into the receive or transmit paths and can be set to buffer
depths of either 32 or 128 bits through the LICR. The 128-bit mode is used in applications where large excursions
of wander are expected. The 32-bit mode is used in delay-sensitive applications. The characteristics of the
attenuators are shown in Figure 21-5. The jitter attenuators can be placed in either the receive path or the transmit
path by appropriately setting or clearing the JAS bit in the LICR. Also, setting the DJA bit in the LICR can disable
the jitter attenuator (in effect, remove it). For the jitter attenuator to operate properly, a 2.048MHz clock (±50ppm)
must be applied at the MCLK pin. On-board circuitry adjusts either the recovered clock from the clock/data
recovery block or the clock applied at the TCLKI pin to create a smooth jitter-free clock that is used to clock data
out of the jitter attenuator FIFO. It is acceptable to provide a gapped/bursty clock at the TCLKI pin if the jitter
attenuator is placed on the transmit side. If the incoming jitter exceeds either 120UIP-P (buffer depth is 128 bits) or
28UIP-P (buffer depth is 32 bits), the DS21Q59 divides the internal nominal 32.768MHz clock by either 15 or 17
instead of the normal 16 to keep the buffer from overflowing. When the device divides by either 15 or 17, it also
sets the jitter attenuator limit trip (JALT) bit in the receive information register (RIR.5).
0
-0.1
-0.2
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
0
TIME (ns)
SCALED
AM
PLITUDE
50
100
150
200
250
-50
-100
-150
-200
-250
269ns
194ns
219ns
(in
75
W
sy
st
em
s,
1
.0
on
the
sc
al
e=
2.
37
V
peak
in
120
W
sys
te
m
s,
1.
0
on
the
s
ca
le
=
3.
00V
pea
k)
G.703
TEMPLATE
相關PDF資料
PDF描述
DS21S07AS+T&R IC TERMINATOR SCSI 16-SOIC
DS21T05Z/T&R IC TERMINATOR SCSI 150MIL 16SOIC
DS21T07S+T&R IC TERMINATOR SCSI 16-SOIC
DS2250-64-16+ IC MCU 64KB 16MHZ 40-SIMM
DS2251T-128-16 IC MICROCNTRLR 128K 16MHZ 72SIMM
相關代理商/技術參數
參數描述
DS21Q59LN+ 功能描述:網絡控制器與處理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21S07A 制造商:Maxim Integrated Products 功能描述:
DS21S07AE 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube
DS21S07AE/T 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:SCSI Terminator
DS21S07AE/T&R 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:IC TERMINATOR SCSI 20-TSSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*