- 您現在的位置：買賣IC網 > PDF目錄11560 > DS3148N (Maxim Integrated Products)IC 8CH DS3/3 FRAMER 349-BGA PDF資料下載
參數資料
| 型號： | DS3148N |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/89頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 8CH DS3/3 FRAMER 349-BGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 控制器類型： | DS3/E3 調幀器 |
| 接口： | LIU |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 電流 - 電源： | 640mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 349-BGA 裸露焊盤 |
| 供應商設備封裝： | 349-HCBGA（27x27） |
| 包裝： | 托盤 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁
DS3146/DS3146/DS31412 6-/8-/12-Channel DS3/E3 Framers
12 of 89
5.4 Receive Framer System Interface Pins
NAME
TYPE
FUNCTION
ROCLK
O
Receive Output Clock. ROCLK is used to clock data out of the receive framer on RDAT. ROCLK is
normally a buffered (and optionally inverted) version of RCLK. When diagnostic loopback is active, ROCLK
is a buffered (and optionally inverted) version of TICLK. If MC4:ROCLKI = 0, data is clocked out of the
framer on the rising edge of ROCLK. If ROCLKI = 1, data is clocked out on the falling edge of ROCLK.
RDAT
O
Receive Data Output. The incoming DS3/E3 data stream is serially clocked out of the receive framer on the
RDAT pin. RDAT is normally updated on the rising edge of ROCLK. To output data on the falling edge of
RDEN/
RGCLK
O
Receive Data Enable/Receive Gapped Clock. The receive framer can be configured to either output a data
enable (RDEN) or a gapped clock (RGCLK). In data enable mode, RDEN goes active when payload data is
available on the RDAT output pin and inactive when overhead data is present on the RDAT pin. In gapped
clock mode, RGCLK acts as a payload data clock for the RDAT output, toggling for each payload bit
position and not toggling for each framing overhead bit position. In DS3 mode, overhead data is defined as
the M bits, F bits, C bits, X bits, and P bits. In E3 mode, overhead data is defined as the FAS word, RAI bit,
and Sn bit (bits 1 to 12). To configure the receive framer for data enable mode, set MC4:RDENMS = 0. To
configure for gapped clock operation, set MC4:RDENMS = 1. RDEN is normally active high; to make RDEN
active low, set MC4:RDENI = 1. RGCLK normally is the same polarity as RCLK; to invert RGCLK, set
MC4:RDENI = 1.
RSOF
O
Receive Start of Frame. RSOF indicates the DS3 or E3 frame boundary on the incoming receive data
stream. RSOF pulses high for one TICLK cycle during the last bit of each DS3 or E3 frame. RSOF is
normally active high. Set MC4:RSOFI = 1 to make RSOF active low.
RLOS
O
Receive Loss of Signal. RLOS goes high when the receive framer is in a loss-of-signal (LOS) state. It
remains high as long as the LOS state persists and returns low when the framer exits the LOS state. See
Table 7-E and Table 7-F for details on the set and clear criteria for this pin. LOS status is also available
through the LOS status bit in the T3E3SR register.
ROOF
O
Receive Out of Frame. ROOF goes high when the receive framer is in an out-of-frame (OOF) state. It
remains high as long as the OOF state persists and returns low when the framer synchronizes. See Table
7-E and Table 7-F for details on the set and clear criteria for this pin. OOF status is also available through
the OOF status bit in the T3E3SR register.
RECU
I
Receive Error-Counter Update Strobe. Through the AECU control bit in the MC1 register, the device can be
configured to use this asynchronous input to initiate an update of the internal error counters in all the
framers on the device. A 0-to-1 transition on the RECU pin causes the device to load the error counter
registers with the latest internal error counts. This signal must be returned low before a subsequent update
of the error counters can occur. After toggling the RECU pin, the host processor must wait at least 100ns
before reading the error counter registers to allow the device time to load the registers. This signal is
logically ORed with the MECU control bit in MC1. If this signal is not used, it should be wired low.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-24K-IX-S | CONVERTER MOD DC/DC 40V 75W |
| PIC16C54C-20E/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54C-04E/SS | IC MCU OTP 512X12 20SSOP |
| PIC12C509T-04/SM | IC MCU OTP 1KX12 8-SOIJ |
| PIC12C508T-04I/SM | IC MCU OTP 512X12 8-SOIJ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS315 | 制造商:Hubbell Wiring Device-Kellems 功能描述:SWITCH, DECO SER, 3W, 15A 120/277V, BR |
| DS3150 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.3V, DS3/E3/STS-1 Line Interface Unit |
| DS3150DK | 功能描述:網絡開發工具 DS3150 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| DS3150G | 功能描述:IC LIU T3/E3/STS-1 49-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| DS3150GN | 功能描述:IC LIU T3/E3/STS-1 IND 49-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。