參數資料
型號： DSP56303VF100B1
廠商： Freescale Semiconductor
文件頁數： 30/108頁
文件大?。?/td> 0K
描述： IC DSP 24BIT 100MHZ 196-BGA
標準包裝： 630
系列： DSP563xx
類型： 定點
接口： 主機接口，SSI，SCI
時鐘速率： 100MHz
非易失內存： ROM（576 B）
芯片上RAM： 24kB
電壓 - 輸入/輸出： 3.30V
電壓 - 核心： 3.30V
工作溫度： -40°C ~ 100°C
安裝類型： 表面貼裝
封裝/外殼： 196-LBGA
供應商設備封裝： 196-MAPBGA（15x15）
包裝： 托盤
DSP56303 Technical Data, Rev. 11
2-8
Freescale Semiconductor
Specifications
Notes:
1.
When fast interrupts are used and IRQA, IRQB, IRQC, and IRQD are defined as level-sensitive, timings 19 through 21 apply to
prevent multiple interrupt service. To avoid these timing restrictions, the deasserted Edge-triggered mode is recommended
when fast interrupts are used. Long interrupts are recommended for Level-sensitive mode.
2.
This timing depends on several settings:
For PLL disable, using internal oscillator (PLL Control Register (PCTL) Bit 16 = 0) and oscillator disabled during Stop (PCTL
Bit 17 = 0), a stabilization delay is required to assure that the oscillator is stable before programs are executed. Resetting the
Stop delay (Operating Mode Register Bit 6 = 0) provides the proper delay. While Operating Mode Register Bit 6 = 1 can be set,
it is not recommended, and these specifications do not guarantee timings for that case.
For PLL disable, using internal oscillator (PCTL Bit 16 = 0) and oscillator enabled during Stop (PCTL Bit 17=1), no
stabilization delay is required and recovery is minimal (Operating Mode Register Bit 6 setting is ignored).
For PLL disable, using external clock (PCTL Bit 16 = 1), no stabilization delay is required and recovery time is defined by the
PCTL Bit 17 and Operating Mode Register Bit 6 settings.
For PLL enable, if PCTL Bit 17 is 0, the PLL is shutdown during Stop. Recovering from Stop requires the PLL to get locked.
The PLL lock procedure duration, PLL Lock Cycles (PLC), may be in the range of 0 to 1000 cycles. This procedure occurs in
parallel with the stop delay counter, and stop recovery ends when the last of these two events occurs. The stop delay counter
completes count or PLL lock procedure completion.
PLC value for PLL disable is 0.
The maximum value for ETC is 4096 (maximum MF) divided by the desired internal frequency (that is, for 66 MHz it is 4096/66
MHz = 62
s). During the stabilization period, TC, TH, and TL is not constant, and their width may vary, so timing may vary as
well.
3.
Periodically sampled and not 100 percent tested.
4.
Value depends on clock source:
For an external clock generator, RESET duration is measured while RESET is asserted, VCC is valid, and the EXTAL input is
active and valid.
For an internal oscillator, RESET duration is measured while RESET is asserted and VCC is valid. The specified timing
reflects the crystal oscillator stabilization time after power-up. This number is affected both by the specifications of the crystal
and other components connected to the oscillator and reflects worst case conditions.
When the VCC is valid, but the other “required RESET duration” conditions (as specified above) have not been yet met, the
device circuitry is in an uninitialized state that can result in significant power consumption and heat-up. Designs should
minimize this state to the shortest possible duration.
5.
If PLL does not lose lock.
6.
VCC = 3.3 V ± 0.3 V; TJ = –40°C to +100°C, CL = 50 pF.
7.
WS = number of wait states (measured in clock cycles, number of TC).
8.
Use the expression to compute a maximum value.
Figure 2-3.
Reset Timing
Table 2-7.
Reset, Stop, Mode Select, and Interrupt Timing6 (Continued)
No.
Characteristics
Expression
100 MHz
Unit
Min
Max
VIH
RESET
Reset Value
First Fetch
All Pins
A[0–17]
8
9
10
相關PDF資料
PDF描述
VI-24D-EU CONVERTER MOD DC/DC 85V 200W
HMC30DRYH-S734 CONN EDGECARD 60POS DIP .100 SLD
TACR475M010XTA CAP TANT 4.7UF 10V 20% 0805
VI-24B-EU CONVERTER MOD DC/DC 95V 200W
VE-B6Y-CX-S CONVERTER MOD DC/DC 3.3V 49.5W
相關代理商/技術參數
參數描述
DSP56303VF100R2 功能描述:數字信號處理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56303VL100 功能描述:數字信號處理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56303VL100B1 功能描述:數字信號處理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56304GC66 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
DSP56304GC80 制造商:未知廠家 制造商全稱:未知廠家 功能描述:24-Bit Digital Signal Processor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*