參數資料
型號： EVAL-AD7923CBZ
廠商： Analog Devices Inc
文件頁數： 10/24頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD7923
標準包裝： 1
ADC 的數量： 1
位數： 12
采樣率（每秒）： 200k
數據接口： 串行
輸入范圍： 0 ~ 2.5 V
在以下條件下的電源（標準）： 7.5mW @ 200kSPS，5 V
工作溫度： -40°C ~ 125°C
已用 IC / 零件： AD7923
已供物品： 板，CD
相關產品： AD7923BRUZ-REEL7TR-ND - IC ADC 12BIT 4CH W/SEQ 16TSSOP
AD7923BRUZ-REEL-ND - IC ADC 12BIT 4CH W/SEQ 16TSSOP
AD7923BRUZ-ND - IC ADC 12BIT 4CH W/SEQ 16TSSOP
AD7923
Data Sheet
Rev. D | Page 18 of 24
Only a portion of the cycle time is taken up by the conversion
time and the dummy transfer for wakeup. In this mode, the
power con-sumption of the part is greatly reduced because the
part enters shutdown at the end of each conversion. When the
control register is programmed to move into auto shutdown, it
does so at the end of the conversion. The user can move the
ADC in and out of the low power state by controlling the CS
signal.
POWERING UP THE AD7923
When supplies are first applied to the AD7923, the ADC can
power up in any of the operating modes of the part. To ensure
that the part is placed into the required operating mode, the
user should perform a dummy cycle operation, as outlined in
The dummy conversion operation must be performed to place
the part into the desired mode of operation. To ensure that the
part is in normal mode, this dummy cycle operation can be
performed with the DIN line tied high, that is, PM1, PM0 = 1, 1
(depending on other required settings in the control register),
but the minimum power-up time of 1 s must be allowed from
the rising edge of CS, where the control register is updated,
before attempting the first valid conversion. This is to allow for
the possibility that the part initially powered up in shutdown.
If the desired mode of operation is full shutdown, then again
only one dummy cycle is required after supplies are applied. In
this dummy cycle, the user simply sets the power management
bits, PM1, PM0 = 1, 0, and upon the rising edge of CS at the
end of that serial transfer, the part enters full shutdown. If the
desired mode of operation is auto shutdown after supplies are
applied, two dummy cycles are required, the first with DIN tied
high and the second dummy cycle to set the power manage-
ment bits PM1 and PM0 = 0,1. On the second CS rising edge
after the supplies are applied, the control register contains the
correct information and the part enters auto shutdown mode as
programmed. If power consumption is of critical concern, then
in the first dummy cycle the user may set PM1, PM0 = 1, 0, that
is, full shutdown, and then place the part into auto shutdown in
the second dummy cycle. For illustration purposes, Figure 25 is
shown with DIN tied high on the first dummy cycle in this case.
Figure 23, Figure 24, and Figure 25 each show the required
dummy cycle(s) after supplies are applied in the case of normal
mode, full shutdown mode, and auto shutdown mode, respect-
ively, being the desired mode of operation.
CS
SCLK
DOUT
DIN
1
14
16
1
14
16
PART IS IN FULL
SHUTDOWN
PART BEGINS TO POWER UP ON
CS RISING EDGE AS PM1 = PM0 =1
THE PART IS FULLY POWERED UP
ONCE
tPOWER UP HAS ELAPSED
CONTROL REGISTER IS LOADED ON THE
FIRST 12 CLOCKS. PM1 = 1, PM0 = 1
TO KEEP THE PART IN NORMAL MODE, LOAD
PM1 = PM0 = 1 IN CONTROL REGISTER
CHANNEL IDENTIFIER BITS + CONVERSION RESULT
DATA INTO CONTROL REGISTER
t12
03086-021
Figure 21. Full Shutdown Mode Operation
1
CS
SCLK
DOUT
DIN
16
1
16
1
16
DUMMY CONVERSION
CHANNEL IDENTIFIER BITS + CONVERSION RESULT
INVALID DATA
CHANNEL IDENTIFIER BITS + CONVERSION RESULT
CONTROL REGISTER IS LOADED ON THE
FIRST 12 CLOCKS, PM1 = 0, PM0 = 1
CONTROL REGISTER CONTENTS SHOULD
NOT CHANGE, WRITE BIT = 0
TO KEEP PART IN THIS MODE, LOAD PM1 = 0, PM0 = 1
IN CONTROL REGISTER OR SET WRITE BIT = 0
PART IS FULLY
POWERED UP
PART BEGINS
TO POWER
UP ON CS
FALLING EDGE
PART ENTERS
SHUTDOWN ON CS
RISING EDGE AS
PM1 = 0, PM0 =1
12
PART ENTERS
SHUTDOWN ON CS
RISING EDGE AS
PM1 = 0, PM0 =1
DATA INTO CONTROL REGISTER
03086-022
Figure 22. Auto Shutdown Mode Operation
相關PDF資料
PDF描述
AT-S-26-8/8/W-25-OE-R MOD CORD SGL-ENDED 8-8 WHITE 25'
NRS8030T1R0NJGJ INDUCTOR POWER 1.0UH 6.2A SMD
GCC28DCMT CONN EDGECARD 56POS .100" WW
EVAL-AD7899CBZ BOARD EVAL FOR AD7899
VI-BND-EY CONVERTER MOD DC/DC 85V 50W
相關代理商/技術參數
參數描述
EVAL-AD7927CB 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD. - Bulk
EVAL-AD7927CBZ 功能描述:BOARD EVALUATION FOR AD7927 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7933CB 制造商:Analog Devices 功能描述:EVALUATION BOARD 4-CHANNEL, 1.5 MSPS, 10-BIT AND 12-BIT PARALLEL ADCS WITH A SEQUENCER 制造商:Analog Devices 功能描述:EVAL BD FOR 4-CH, 1.5 MSPS, 10-BIT AND 12-BIT PARALLEL ADCS - Bulk
EVAL-AD7934-6CB 制造商:Analog Devices 功能描述:EVAL BD 4-CH, 1.5 MSPS, 10-BIT AND 12-BIT PARALLEL ADCS W/ A - Bulk
EVAL-AD7934CB 制造商:Analog Devices 功能描述:Evaluation Board For 4-Channel, 1.5 MSPS, 10-Bit And 12-Bit Parallel ADCs With A Sequencer 制造商:Analog Devices 功能描述:EVAL BD 4-CH, 1.5 MSPS, 10-BIT AND 12-BIT PARALLEL ADCS W/ A - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*