參數資料
型號: EVAL-ADUC841QSPZ
廠商: Analog Devices Inc
文件頁數: 71/88頁
文件大小: 0K
描述: KIT DEV QUICK START ADUC841
標準包裝: 1
系列: QuickStart™ PLUS 套件
類型: MCU
適用于相關產品: ADuC841
所含物品: 評估板、電源、纜線、軟件、仿真器和說明文檔
ADuC841/ADuC842/ADuC843
Rev. 0 | Page 73 of 88
If access to more than 64 kBytes of RAM is desired, a feature
unique to the ADuC841/ADuC842/ADuC843 allows address-
ing up to 16 MBytes of external RAM simply by adding an
additional latch as illustrated in Figure 79.
LATCH
P2
ALE
P0
LATCH
SRAM
A8–A15
A0–A7
D0–D7
(DATA)
A16–A23
OE
RD
WE
WR
ADuC841/
ADuC842/
ADuC843
03260-0-079
Figure 79. External Data Memory Interface (16 MBytes Address Space)
In either implementation, Port 0 (P0) serves as a multiplexed
address/data bus. It emits the low byte of the data pointer (DPL)
as an address, which is latched by a pulse of ALE prior to data
being placed on the bus by the ADuC841/ADuC842/ADuC843
(write operation) or by the SRAM (read operation). Port 2 (P2)
provides the data pointer page byte (DPP) to be latched by ALE,
followed by the data pointer high byte (DPH). If no latch is
connected to P2, DPP is ignored by the SRAM, and the 8051
standard of 64 kBytes external data memory access is maintained.
Power Supplies
The operational power supply voltage of the parts depends on
whether the part is the 3 V version or the 5 V version. The
specifications are given for power supplies within 2.7 V to 3.6 V
or ±5% of the nominal 5 V level.
Note that Figure 80 and Figure 81 refer to the PQFP package.
For the CSP package, connect the extra DVDD, DGND, AVDD,
and AGND in the same manner. Also, the paddle on the bottom
of the package should be soldered to a metal plate to provide
mechanical stability. This metal plate should not be connected
to ground.
Separate analog and digital power supply pins (AVDD and DVDD,
respectively) allow AVDD to be kept relatively free of the noisy
digital signals that are often present on the system DVDD line.
However, though you can power AVDD and DVDD from two
separate supplies if desired, you must ensure that they remain
within ±0.3 V of one another at all times to avoid damaging the
chip (as per the Absolute Maximum Ratings section). Therefore,
it is recommended that unless AVDD and DVDD are connected
directly together, back-to-back Schottky diodes should be con-
nected between them, as shown in Figure 80.
DVDD
AGND
AVDD
+
0.1
F
10
F
ANALOG SUPPLY
10
F
DGND
0.1
F
DIGITAL SUPPLY
+
ADuC841/
ADuC842/
ADuC843
03260-0-080
Figure 80. External Dual-Supply Connections
As an alternative to providing two separate power supplies, the
user can help keep AVDD quiet by placing a small series resistor
and/or ferrite bead between it and DVDD, and then decoupling
AVDD separately to ground. An example of this configuration is
shown in Figure 81. With this configuration, other analog
circuitry (such as op amps and voltage reference) can be powered
from the AVDD supply line as well. The user will still want to
include back-to-back Schottky diodes between AVDD and DVDD
to protect them from power-up and power-down transient
conditions that could momentarily separate the two supply voltages.
DVDD
AGND
AVDD
DGND
DIGITAL SUPPLY
+
BEAD
1.6
0.1
F
0.1
F
10
F
10
F
ADuC841/
ADuC842/
ADuC843
03260-0-081
Figure 81. External Single-Supply Connections
Notice that in both Figure 80 and Figure 81, a large value
(10 F) reservoir capacitor sits on DVDD and a separate 10 F
capacitor sits on AVDD. Also, local small-value (0.1 F) capaci-
tors are located at each VDD pin of the chip. As per standard
design practice, be sure to include all of these capacitors, and
ensure the smaller capacitors are close to each AVDD pin with
trace lengths as short as possible. Connect the ground terminal
of each of these capacitors directly to the underlying ground
plane. Finally, note that at all times, the analog and digital ground
pins on the part must be referenced to the same system ground
reference point.
相關PDF資料
PDF描述
AT97SC3204T-X1K180 KIT DEV EMBEDDED TPM TWI
RPS-1K-16-10/2.0-9 HEAT SHRINK SLEEVE
ATF15XX-DK3 KIT DEV FOR ATF15XX CPLD'S
ADR02WARZ-REEL7 IC VREF SERIES PREC 5V 8-SOIC
EVAL-ADUC812QSZ BOARD EVALUATION FOR ADUC812
相關代理商/技術參數
參數描述
EVAL-ADUC841QSPZ 制造商:Analog Devices 功能描述:Silicon Manufacturer:Analog Devices C
EVAL-ADUC841QSZ 功能描述:KIT DEV FOR ADUC841 QUICK START RoHS:是 類別:編程器,開發系統 >> 通用嵌入式開發板和套件(MCU、DSP、FPGA、CPLD等) 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206,PIC16F690,PIC16F819 所含物品:板,線纜,元件,CD,PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
EVAL-ADUC842QS 功能描述:KIT DEV FOR ADUC842 QUICK START RoHS:否 類別:編程器,開發系統 >> 通用嵌入式開發板和套件(MCU、DSP、FPGA、CPLD等) 系列:QuickStart™ 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板,軟件,4x4 鍵盤,光學撥輪,QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
EVAL-ADUC842QS1 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
EVAL-ADUC842QSP1 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU