參數資料
型號： FS7VS-5
廠商： Mitsubishi Electric Corporation
英文描述： HIGH-SPEED SWITCHING USE
中文描述： 高速開關使用
文件頁數： 47/91頁
文件大小： 488K
代理商： FS7VS-5
PSD9XX Family
PSD935G2
46
The
PSD935G2
Functional
Blocks
(cont.)
9.4 I/OPorts
There are seven programmable I/O ports: Ports A, B, C, D, E, F and G. Each of the ports
is eight bits except Port D, which is 4 bits. Each port pin is individually user configurable,
thus allowing multiple functions per port. The ports are configured using PSDsoft or by the
microcontroller writing to on-chip registers in the CSIOP address space.
The topics discussed in this section are:
General Port Architecture
Port Operating Modes
Port Configuration Registers
Port Data Registers
Individual Port Functionality.
9.4.1 General Port Architecture
The general architecture of the I/O Port is shown in Figure 20. Individual Port architectures
are shown in Figures 21 through 23. In general, once the purpose for a port pin has been
defined, that pin will no longer be available for other purposes. Exceptions will be noted.
As shown in Figure 20, the ports contain an output multiplexer whose selects are driven
by the configuration bits in the Control Registers (Ports E, F and G only) and PSDsoft
Configuration. Inputs to the multiplexer include the following:
J
Output data from the Data Out Register
J
Latched address outputs
J
GPLD outputs (External Chip Selects)
The Port Data Buffer (PDB) is a tri-state buffer that allows only one source at a time to be
read. The PDB is connected to the Internal Data Bus for feedback and can be read by the
microcontroller. The Data Out and Micro
Cell outputs, Direction and Control Registers,
and port pin input are all connected to the PDB.
The contents of these registers can be altered by the microcontroller. The PDB feedback
path allows the microcontroller to check the contents of the registers.
9.4.2 Port Operating Modes
The I/O Ports have several modes of operation. Some modes can be defined using
PSDsoft, some by the microcontroller writing to the Registers in CSIOP space, and some
by both. The modes that can only be defined using PSDsoft must be programmed into the
device and cannot be changed unless the device is reprogrammed. The modes that can be
changed by the microcontroller can be done so dynamically at run-time. The PLD I/O,
Data Port, Address Input, and MCU Reset modes are the only modes that must be defined
before programming the device. All other modes can be changed by the microcontroller at
run-time.
Table 16 summarizes which modes are available on each port. Table 19 shows how and
where the different modes are configured. Each of the port operating modes are described
in the following subsections.
相關PDF資料
PDF描述
PSD935F3V-15B81 Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD935F3V-15B81I Ceramic Chip Capacitors / MIL-PRF-55681; Capacitance [nom]: 30000uF; Working Voltage (Vdc)[max]: 100V; Capacitance Tolerance: +/-0.1pF; Dielectric: Multilayer Ceramic; Temperature Coefficient: C0G (NP0); Lead Style: Surface Mount Chip; Lead Dimensions: 0805; Termination: Solder Coated (Sn/Pb, 70/30); Body Dimensions: 0.080" x 0.050" x 0.055"; Container: Bag; Features: MIL-PRF-55681: S Failure Rate
PSD935F3V-15J Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD935F3V-15JI Configurable Memory System on a Chip for 8-Bit Microcontrollers
PSD935F3V-15M Configurable Memory System on a Chip for 8-Bit Microcontrollers
相關代理商/技術參數
參數描述
FS-8000 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:MULTI-USER KVM SWITCH
FS-80-0-300V 制造商:Fuji Electric 功能描述:
FS800R06KE3_H7E 制造商:Infineon Technologies AG 功能描述:
FS800R07A2E3 功能描述:IGBT 模塊 IGBT Module 650V 700A RoHS:否 制造商:Infineon Technologies 產品:IGBT Silicon Modules 配置:Dual 集電極—發射極最大電壓 VCEO:600 V 集電極—射極飽和電壓:1.95 V 在25 C的連續集電極電流:230 A 柵極—射極漏泄電流:400 nA 功率耗散:445 W 最大工作溫度:+ 125 C 封裝 / 箱體:34MM 封裝:
FS800R07A2E3BOSA2 制造商:Infineon Technologies AG 功能描述:Trans IGBT Module N-CH 650V 700A 33-Pin
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*