參數資料
型號： GS9092-CNE3
廠商： Gennum Corporation
英文描述： GS9092 GenLINX-R III 270Mb/s Serializer for SDI and DVB-ASI
中文描述： GS9092 GenLINX - R的第三270Mb / s的串行SDI和DVB - ASI在內
文件頁數： 50/58頁
文件大?。?/td> 608K
代理商： GS9092-CNE3
GS9092 Data Sheet
28202 - 2
September 2005
50 of 58
3.13.1 Command Word Description
The command word consists of a 16-bit word transmitted MSB first and contains a
read/write bit, an Auto-Increment bit and a 12-bit address.
Figure 3-11
shows the
command word format and bit configurations.
Command words are clocked into the GS9092 on the rising edge of the serial clock
SCLK, which operates in a burst fashion.
When the Auto-Increment bit is set LOW, each command word must be followed
by only one data word to ensure proper operation. If the Auto-Increment bit is set
HIGH, the following data word will be written into the address specified in the
command word, and subsequent data words will be written into incremental
addresses from the previous data word. This facilitates multiple address writes
without sending a command word for each data word.
Auto-Increment may be used for both read and write access.
3.13.2 Data Read and Write Timing
Read and write mode timing for the GSPI interface is shown in
Figure 3-13
and
Figure 3-14
respectively. The timing parameters are defined in
Table 3-13
.
When several devices are connected to the GSPI chain, only one CS must be
asserted during a read sequence.
During the write sequence, all command and following data words input at the
SDIN pin are output at the SDOUT pin as is. Where several devices are connected
to the GSPI chain, data can be written simultaneously to all the devices that have
CS set LOW.
Table 3-13: GSPI Timing Parameters
Parameter
Definition
Specification
t
0
The minimum duration of time chip select, CS, must be
LOW before the first SCLK rising edge.
1.5 ns
t
1
The minimum SCLK period.
18.5 ns
t
2
Duty cycle tolerated by SCLK.
40% to 60%
t
3
Minimum input setup time.
1.5 ns
t
4
Write Cycle: the minimum duration of time between the
last SCLK command (or data word if the Auto-Increment
bit is HIGH) and the first SCLK of the data word.
37.1 ns
t
5
Read Cycle: the minimum duration of time between the
last SCLK command (or data word if the Auto-Increment
bit is HIGH) and the first SCLK of the data word.
148.4 ns
t
5
Read Cycle - ANC_DATA_RDBACK bit HIGH when FIFO
is in ancillary insertion mode (see
Ancillary Data Insertion
on page 29
): the minimum duration of time between the
last SCLK command (or data word if the Auto-Increment
bit is HIGH) and the first SCLK of the data word.
222.6 ns
相關PDF資料
PDF描述
GSC9620 P-CHANNEL ENHANCEMENT MODE POWER MOSFET
GSD2004S-V-GS08 DIODE 0.225 A, 300 V, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB, ROHS COMPLIANT, PLASTIC PACKAGE-3, Signal Diode
GSD2004S-V-GS18 DIODE 0.225 A, 300 V, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB, ROHS COMPLIANT, PLASTIC PACKAGE-3, Signal Diode
GSD2004W-V-GS18 DIODE 0.225 A, 300 V, SILICON, SIGNAL DIODE, ROHS COMPLIANT, PLASTIC PACKAGE-2, Signal Diode
GSD2004W-V-GS08 DIODE 0.225 A, 300 V, SILICON, SIGNAL DIODE, ROHS COMPLIANT, PLASTIC PACKAGE-2, Signal Diode
相關代理商/技術參數
參數描述
GS90A12-P1M 功能描述:插入式交流適配器 80W 12V 6.67A RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V
GS90A15-P1M 功能描述:插入式交流適配器 90W 15V 6A RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V
GS90A19-P1M 功能描述:插入式交流適配器 90W 19V 4.74A RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V
GS90A24-P1M 功能描述:插入式交流適配器 90W 24V 3.75A RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V
GS90A48-P1M 功能描述:插入式交流適配器 90W 48V 1.87A RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*