- 您現在的位置：買賣IC網 > PDF目錄370783 > HYB25D128800ATL-6 (INFINEON TECHNOLOGIES AG) 128 Mbit Double Data Rate SDRAM PDF資料下載
參數資料
| 型號： | HYB25D128800ATL-6 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | 128 Mbit Double Data Rate SDRAM |
| 中文描述： | 128兆雙倍數據速率SDRAM |
| 文件頁數： | 25/85頁 |
| 文件大小： | 3085K |
| 代理商： | HYB25D128800ATL-6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
Data Sheet
25
Rev. 1.0, 2004-04
HYB25D128[400/800/160]C[C/E/T](L)
128 Mbit Double Data Rate SDRAM
Functional Description
3.4
Commands
Deselect
The Deselect function prevents new commands from being executed by the DDR SDRAM. The DDR SDRAM is
effectively deselected. Operations already in progress are not affected.
No Operation (NOP)
The No Operation (NOP) command is used to perform a NOP to a DDR SDRAM. This prevents unwanted
commands from being registered during idle or wait states. Operations already in progress are not affected.
Mode Register Set
The mode registers are loaded via inputs A0-A11, BA0 and BA1. See mode register descriptions in
Chapter 3.2
.
The Mode Register Set command can only be issued when all banks are idle and no bursts are in progress. A
subsequent executable command cannot be issued until
t
MRD
is met.
Active
The Active command is used to open (or activate) a row in a particular bank for a subsequent access. The value
on the BA0, BA1 inputs selects the bank, and the address provided on inputs A0-A11 selects the row. This row
remains active (or open) for accesses until a Precharge (or Read or Write with Auto Precharge) is issued to that
bank. A Precharge (or Read or Write with Auto Precharge) command must be issued and completed before
opening a different row in the same bank.
Read
The Read command is used to initiate a burst read access to an active (open) row. The value on the BA0, BA1
inputs selects the bank, and the address provided on inputs A0-Ai, Aj (where [i = 8, j = don’t care] for x16, [i = 9,
j = don’t care] for x8 and [i = 9, j = 11] for x4) selects the starting column location. The value on input A10
determines whether or not Auto Precharge is used. If Auto Precharge is selected, the row being accessed is
precharged at the end of the Read burst; if Auto Precharge is not selected, the row remains open for subsequent
accesses.
Write
The Write command is used to initiate a burst write access to an active (open) row. The value on the BA0, BA1
inputs selects the bank, and the address provided on inputs A0-Ai, Aj (where [i = 9, j = don’t care] for x8; where
[i = 9, j = 11] for x4) selects the starting column location. The value on input A10 determines whether or not Auto
Precharge is used. If Auto Precharge is selected, the row being accessed is precharged at the end of the Write
burst; if Auto Precharge is not selected, the row remains open for subsequent accesses. Input data appearing on
the DQs is written to the memory array subject to the DM input logic level appearing coincident with the data. If a
given DM signal is registered low, the corresponding data is written to memory; if the DM signal is registered high,
the corresponding data inputs are ignored, and a Write is not executed to that byte/column location.
Precharge
The Precharge command is used to deactivate (close) the open row in a particular bank or the open row(s) in all
banks. The bank(s) will be available for a subsequent row access a specified time (
t
RP
) after the Precharge
command is issued. Input A10 determines whether one or all banks are to be precharged, and in the case where
only one bank is to be precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are treated as “Don’t
Care”. Once a bank has been precharged, it is in the idle state and must be activated prior to any Read or Write
commands being issued to that bank. A precharge command is treated as a NOP if there is no open row in that
bank, or if the previously open row is already in the process of precharging.
相關PDF資料 |
PDF描述 |
|---|---|
| HYB25D128400ATL-7 | 128 Mbit Double Data Rate SDRAM |
| HYB25D128800ATL-7 | 128 Mbit Double Data Rate SDRAM |
| HYB25D128160TCL-75 | MEMORY SPECTRUM |
| HYB25D128160TCL-7F | MEMORY SPECTRUM |
| HYB25D128160TE-37 | MEMORY SPECTRUM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HYB25D128800ATL-7 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:128 Mbit Double Data Rate SDRAM |
| HYB25D128800ATL-8 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:128 Mbit Double Data Rate SDRAM |
| HYB25D128800C | 制造商:QIMONDA 制造商全稱:QIMONDA 功能描述:128-Mbit Double-Data-Rate SDRAM |
| HYB25D128800CC-5 | 制造商:QIMONDA 制造商全稱:QIMONDA 功能描述:128-Mbit Double-Data-Rate SDRAM |
| HYB25D128800CC-6 | 制造商:QIMONDA 制造商全稱:QIMONDA 功能描述:128-Mbit Double-Data-Rate SDRAM |
發布緊急采購，3分鐘左右您將得到回復。