- 您現在的位置：買賣IC網 > PDF目錄9574 > IDT82V3355TFG (IDT, Integrated Device Technology Inc)IC PLL WAN SYNC ETH 64-TQFP PDF資料下載
參數資料
| 型號： | IDT82V3355TFG |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 53/135頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PLL WAN SYNC ETH 64-TQFP |
| 標準包裝： | 1 |
| 類型： | 時鐘/頻率發生器，多路復用器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，Stratum |
| 輸入： | CMOS，LVDS，PECL |
| 輸出： | CMOS，LVDS，PECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 3:2 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 622.08MHz |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-TQFP（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | 82V3355TFG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁
IDT82V3355
SYNCHRONOUS ETHERNET WAN PLL
Functional Description
24
May 19, 2009
3.7
SELECTED INPUT CLOCK MONITORING
The quality of the selected input clock is always monitored (refer to
Chapter 3.5 Input Clock Quality Monitoring) and the DPLL locking status
is always monitored.
3.7.1
T0 / T4 DPLL LOCKING DETECTION
The following events is always monitored:
Fast Loss;
Coarse Phase Loss;
Fine Phase Loss;
Hard Limit Exceeding.
3.7.1.1
Fast Loss
A fast loss is triggered when the selected input clock misses 2 con-
secutive clock cycles. It is cleared once an active clock edge is detected.
For T0 path, the occurrence of the fast loss will result in T0 DPLL
unlocked if the FAST_LOS_SW bit is ‘1’. For T4 path, the occurrence of
the fast loss will result in T4 DPLL unlocked regardless of the
FAST_LOS_SW bit.
3.7.1.2
Coarse Phase Loss
The T0/T4 DPLL compares the selected input clock with the feed-
back signal. If the phase-compared result exceeds the coarse phase
limit, a coarse phase loss is triggered. It is cleared once the phase-com-
pared result is within the coarse phase limit.
When the selected input clock is of 2 kHz, 4 kHz or 8 kHz, the coarse
phase limit depends on the MULTI_PH_8K_4K_2K_EN bit, the
WIDE_EN bit and the PH_LOS_COARSE_LIMT[3:0] bits. Refer to
Table 11. When the selected input clock is of other frequencies but 2
kHz, 4 kHz and 8 kHz, the coarse phase limit depends on the WIDE_EN
bit and the PH_LOS_COARSE_LIMT[3:0] bits. Refer to Table 12.
The occurrence of the coarse phase loss will result in T0/T4 DPLL
unlocked if the COARSE_PH_LOS_LIMT_EN bit is ‘1’.
3.7.1.3
Fine Phase Loss
The T0/T4 DPLL compares the selected input clock with the feed-
back signal. If the phase-compared result exceeds the fine phase limit
programmed by the PH_LOS_FINE_LIMT[2:0] bits, a fine phase loss is
triggered. It is cleared once the phase-compared result is within the fine
phase limit.
The occurrence of the fine phase loss will result in T0/T4 DPLL
unlocked if the FINE_PH_LOS_LIMT_EN bit is ‘1’.
3.7.1.4
Hard Limit Exceeding
Two limits are available for this monitoring. They are DPLL soft limit
and DPLL hard limit. When the frequency of the DPLL output with
respect to the master clock exceeds the DPLL soft / hard limit, a DPLL
soft / hard alarm will be raised; the alarm is cleared once the frequency
is within the corresponding limit. The occurrence of the DPLL soft alarm
does not affect the T0/T4 DPLL locking status. The DPLL soft alarm is
indicated by the corresponding T0_DPLL_SOFT_FREQ_ALARM /
T4_DPLL_SOFT_FREQ_ALARM bit. The occurrence of the DPLL hard
alarm will result in T0/T4 DPLL unlocked if the FREQ_LIMT_PH_LOS bit
is ‘1’.
The DPLL soft limit is set by the DPLL_FREQ_SOFT_LIMT[6:0] bits
and can be calculated as follows:
DPLL Soft Limit (ppm) = DPLL_FREQ_SOFT_LIMT[6:0] X 0.724
The DPLL hard limit is set by the DPLL_FREQ_HARD_LIMT[15:0]
bits and can be calculated as follows:
DPLL Hard Limit (ppm) = DPLL_FREQ_HARD_LIMT[15:0] X 0.0014
3.7.2
LOCKING STATUS
The DPLL locking status depends on the locking monitoring results.
The DPLL is in locked state if none of the following events is triggered
during 2 seconds; otherwise, the DPLL is unlocked.
Fast Loss (the FAST_LOS_SW bit is ‘1’);
Coarse Phase Loss (the COARSE_PH_LOS_LIMT_EN bit is
‘1’);
Fine Phase Loss (the FINE_PH_LOS_LIMT_EN bit is ‘1’);
DPLL Hard Alarm (the FREQ_LIMT_PH_LOS bit is ‘1’).
If the FAST_LOS_SW bit, the COARSE_PH_LOS_LIMT_EN bit, the
FINE_PH_LOS_LIMT_EN bit or the FREQ_LIMT_PH_LOS bit is ‘0’, the
DPLL locking status will not be affected even if the corresponding event
is triggered. If all these bits are ‘0’, the DPLL will be in locked state in 2
seconds.
The DPLL locking status is indicated by the T0_DPLL_LOCK /
T4_DPLL_LOCK bit.
The T4_STS 1 bit will be set when the locking status of the T4 DPLL
changes (from ‘lock’ to ‘unlock’ or from ‘unlock’ to ‘lock’). If the T4_STS 2
bit is ‘1’, an interrupt will be generated.
Table 11: Coarse Phase Limit Programming (the selected input
clock of 2 kHz, 4 kHz or 8 kHz)
MULTI_PH_8K_4K
_2K_EN
WIDE_EN
Coarse Phase Limit
0
don’t-care
±1 UI
1
0±1 UI
1
set by the PH_LOS_COARSE_LIMT[3:0] bits
Table 12: Coarse Phase Limit Programming (the selected input
clock of other than 2 kHz, 4 kHz and 8 kHz)
WIDE_EN
Coarse Phase Limit
0±1 UI
1
set by the PH_LOS_COARSE_LIMT[3:0] bits
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26SF11PA | CONN PLUG 11POS STRAIGHT W/PINS |
| VE-B2V-MW-F4 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-B2T-MW-F1 | CONVERTER MOD DC/DC 6.5V 100W |
| D38999/26MH21SA | CONN PLUG 21POS STRAIGHT W/SCKT |
| MS3450L18-9S | CONN RCPT 7POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82V3355TFG8 | 功能描述:IC PLL WAN SYNC ETH 64-TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| IDT82V3355TFGBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:SYNCHRONOUS ETHERNET WAN PLL |
| IDT82V3358 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:SYNCHRONOUS ETHERNET WAN PLL |
| IDT82V3358EDG | 功能描述:IC PLL WAN SYNC ETHERNET 64TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| IDT82V3358EDG8 | 制造商:Integrated Device Technology Inc 功能描述:IC PLL WAN SYNC ETHERNET 64TQFP |
發布緊急采購，3分鐘左右您將得到回復。