- 您現在的位置：買賣IC網 > PDF目錄9574 > IDT82V3355TFG (IDT, Integrated Device Technology Inc)IC PLL WAN SYNC ETH 64-TQFP PDF資料下載
參數資料
| 型號： | IDT82V3355TFG |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 61/135頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PLL WAN SYNC ETH 64-TQFP |
| 標準包裝： | 1 |
| 類型： | 時鐘/頻率發生器，多路復用器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，Stratum |
| 輸入： | CMOS，LVDS，PECL |
| 輸出： | CMOS，LVDS，PECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 3:2 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 622.08MHz |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-TQFP（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | 82V3355TFG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁
IDT82V3355
SYNCHRONOUS ETHERNET WAN PLL
Functional Description
31
May 19, 2009
3.10
T0 / T4 DPLL OPERATING MODE
The T0/T4 DPLL gives a stable performance in different applications
without being affected by operating conditions or silicon process varia-
tions. It integrates a PFD (Phase & Frequency Detector), a LPF (Low
Pass Filter) and a DCO (Digital Controlled Oscillator), which forms a
closed loop. If no input clock is selected, the loop is not closed, and the
PFD and LPF do not function.
The PFD detects the phase error, including the fast loss, coarse
phase loss and fine phase loss (refer to Chapter 3.7.1.1 Fast Loss to
Chapter 3.7.1.3 Fine Phase Loss). The averaged phase error of the T0/
T4 DPLL feedback with respect to the selected input clock is indicated
by the CURRENT_PH_DATA[15:0] bits. It can be calculated as follows:
Averaged Phase Error (ns) = CURRENT_PH_DATA[15:0] X 0.61
The LPF filters jitters. Its 3 dB bandwidth and damping factor are pro-
grammable. A range of bandwidths and damping factors can be set to
meet different application requirements. Generally, the lower the damp-
ing factor is, the longer the locking time is and the more the gain is.
The DCO controls the DPLL output. The frequency of the DPLL out-
put is always multiplied on the basis of the master clock. The phase and
frequency offset of the DPLL output may be locked to those of the
selected input clock. The current frequency offset with respect to the
master clock is indicated by the CURRENT_DPLL_FREQ[23:0] bits, and
can be calculated as follows:
Current Frequency Offset (ppm) = CURRENT_DPLL_FREQ[23:0] X
0.000011
3.10.1
T0 DPLL OPERATING MODE
The T0 DPLL loop is closed except in Free-Run mode and Holdover
mode.
For a closed loop, different bandwidths and damping factors can be
used depending on DPLL locking stages: starting, acquisition and
locked.
In the first two seconds when the T0 DPLL attempts to lock to the
selected input clock, the starting bandwidth and damping factor are
used. They are set by the T0_DPLL_START_BW[4:0] bits and the
T0_DPLL_START_DAMPING[2:0] bits respectively.
During the acquisition, the acquisition bandwidth and damping factor
are used. They are set by the T0_DPLL_ACQ_BW[4:0] bits and the
T0_DPLL_ACQ_DAMPING[2:0] bits respectively.
When the T0 selected input clock is locked, the locked bandwidth
and damping
factor are
used. They
are
set
by
the
T0_DPLL_LOCKED_BW[4:0]
bits
and
the
T0_DPLL_LOCKED_DAMPING[2:0] bits respectively.
The corresponding bandwidth and damping factor are used when the
T0 DPLL operates in different DPLL locking stages: starting, acquisition
and locked, as controlled by the device automatically.
Only the locked bandwidth and damping factor can be used regard-
less of the T0 DPLL locking stage, as controlled by the AUTO_BW_SEL
bit.
3.10.1.1
Free-Run Mode
In Free-Run mode, the T0 DPLL output refers to the master clock
and is not affected by any input clock. The accuracy of the T0 DPLL out-
put is equal to that of the master clock.
3.10.1.2
Pre-Locked Mode
In Pre-Locked mode, the T0 DPLL output attempts to track the
selected input clock.
The Pre-Locked mode is a secondary, temporary mode.
3.10.1.3
Locked Mode
In Locked mode, the T0 selected input clock is locked. The phase
and frequency offset of the T0 DPLL output track those of the T0
selected input clock.
In this mode, if the T0 selected input clock is in fast loss status and
the FAST_LOS_SW bit is ‘1’, the T0 DPLL is unlocked (refer to
Chapter 3.7.1.1 Fast Loss) and will enter Lost-Phase mode when the
operating mode is switched automatically; if the T0 selected input clock
is in fast loss status and the FAST_LOS_SW bit is ‘0’, the T0 DPLL lock-
ing status is not affected and the T0 DPLL will enter Temp-Holdover
mode automatically.
3.10.1.3.1 Temp-Holdover Mode
The T0 DPLL will automatically enter Temp-Holdover mode with a
selected input clock switch or no qualified input clock available when the
operating mode switch is under external control.
In Temp-Holdover mode, the T0 DPLL has temporarily lost the
selected input clock. The T0 DPLL operation in Temp-Holdover mode
and that in Holdover mode are alike (refer to Chapter 3.10.1.5 Holdover
Mode) except the frequency offset acquiring methods. See
Chapter 3.10.1.5 Holdover Mode for details about the methods. The
method is selected by the TEMP_HOLDOVER_MODE[1:0] bits, as
shown in Table 19:
The device automatically controls the T0 DPLL to exit from Temp-
Holdover mode.
3.10.1.4
Lost-Phase Mode
In Lost-Phase mode, the T0 DPLL output attempts to track the
selected input clock.
The Lost-Phase mode is a secondary, temporary mode.
3.10.1.5
Holdover Mode
In Holdover mode, the T0 DPLL resorts to the stored frequency data
acquired in Locked mode to control its output. The T0 DPLL output is not
Table 19: Frequency Offset Control in Temp-Holdover Mode
TEMP_HOLDOVER_MODE[1:0]
Frequency Offset Acquiring Method
00
the same as that used in Holdover mode
01
Automatic Instantaneous
10
Automatic Fast Averaged
11
Automatic Slow Averaged
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26SF11PA | CONN PLUG 11POS STRAIGHT W/PINS |
| VE-B2V-MW-F4 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-B2T-MW-F1 | CONVERTER MOD DC/DC 6.5V 100W |
| D38999/26MH21SA | CONN PLUG 21POS STRAIGHT W/SCKT |
| MS3450L18-9S | CONN RCPT 7POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82V3355TFG8 | 功能描述:IC PLL WAN SYNC ETH 64-TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| IDT82V3355TFGBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:SYNCHRONOUS ETHERNET WAN PLL |
| IDT82V3358 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:SYNCHRONOUS ETHERNET WAN PLL |
| IDT82V3358EDG | 功能描述:IC PLL WAN SYNC ETHERNET 64TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| IDT82V3358EDG8 | 制造商:Integrated Device Technology Inc 功能描述:IC PLL WAN SYNC ETHERNET 64TQFP |
發布緊急采購，3分鐘左右您將得到回復。