- 您現在的位置：買賣IC網 > PDF目錄9574 > IDT82V3355TFG (IDT, Integrated Device Technology Inc)IC PLL WAN SYNC ETH 64-TQFP PDF資料下載
參數資料
| 型號： | IDT82V3355TFG |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 55/135頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PLL WAN SYNC ETH 64-TQFP |
| 標準包裝： | 1 |
| 類型： | 時鐘/頻率發生器，多路復用器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，Stratum |
| 輸入： | CMOS，LVDS，PECL |
| 輸出： | CMOS，LVDS，PECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 3:2 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 622.08MHz |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-TQFP（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | 82V3355TFG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁
IDT82V3355
SYNCHRONOUS ETHERNET WAN PLL
Functional Description
26
May 19, 2009
3.8
SELECTED INPUT CLOCK SWITCH
If the input clock is selected by External Fast selection or by Forced
selection, it can be switched by setting the related registers (refer to
Selection) any time. In this case, whether the input clock is qualified for
DPLL locking does not affect the clock switch. If the T4 selected input
clock is a T0 DPLL output, it can only be switched by setting the
T0_FOR_T4 bit.
When the input clock is selected by Automatic selection, the input
clock switch depends on its validity and priority. If the current selected
input clock is disqualified, a new qualified input clock may be switched
to.
3.8.1
INPUT CLOCK VALIDITY
For all the input clocks, the validity depends on the results of input
clock quality monitoring (refer to Chapter 3.5 Input Clock Quality Moni-
toring). When all of the following conditions are satisfied, the input clock
is valid; otherwise, it is invalid.
No no-activity alarm (the INn_CMOS_NO_ACTIVITY_ALARM /
INn_DIFF_NO_ACTIVITY_ALARM bit is ‘0’);
No frequency hard alarm (the INn_CMOS_FREQ_HARD_
ALARM / INn_DIFF_FREQ_HARD_ALARM bit is ‘0’);
If the IN_NOISE_WINDOW bit is ‘1’, all the edges of the input
clock of 2 kHz, 4 kHz or 8 kHz drift inside ±5%; if the
IN_NOISE_WINDOW bit is ‘0’, this condition is ignored.
The validity qualification of the T0 selected input clock is different
from that of the T4 selected input clock. The validity qualification of the
T4 selected input clock is the same as the above. The T0 selected input
clock is valid when all of the above and the following conditions are sat-
isfied; otherwise, it is invalid.
No phase lock alarm, i.e., the INn_CMOS_PH_LOCK_ALARM /
INn_DIFF_PH_LOCK_ALARM bit is ‘0’;
If the ULTR_FAST_SW bit is ‘1’, the T0 selected input clock
misses less than (<) 2 consecutive clock cycles; if the
ULTR_FAST_SW bit is ‘0’, this condition is ignored.
The validities of all the input clocks are indicated by the INn_CMOS 1
bit (n = 1, 2 or 3) / INn_DIFF 1 bit (n = 1 or 2). When the input clock valid-
ity changes (from ‘valid’ to ‘invalid’ or from ‘invalid’ to ‘valid’), the
INn_CMOS 2 / INn_DIFF 2 bit will be set. If the INn_CMOS 3 / INn_DIFF
3 bit is ‘1’, an interrupt will be generated.
When the T0 selected input clock has failed, i.e., the validity of the T0
selected input clock changes from ‘valid’ to ‘invalid’, the
T0_MAIN_REF_FAILED 1 bit will be set. If the T0_MAIN_REF_FAILED 2
bit is ‘1’, an interrupt will be generated. This interrupt can also be indi-
cated by hardware - the TDO pin, as determined by the
LOS_FLAG_TO_TDO bit. When the TDO pin is used to indicate this
interrupt, it will be set high when this interrupt is generated and will
remain high until this interrupt is cleared.
3.8.2
SELECTED INPUT CLOCK SWITCH
When the device is configured as Automatic input clock selection, T0
input clock switch is different from T4 input clock switch.
For T0 path, Revertive and Non-Revertive switches are supported,
as selected by the REVERTIVE_MODE bit.
For T4 path, only Revertive switch is supported.
The difference between Revertive and Non-Revertive switches is
that whether the selected input clock is switched when another qualified
input clock with a higher priority than the current selected input clock is
available for selection. In Non-Revertive switch, input clock switch is
minimized.
Conditions of the qualified input clocks available for T0 selection are
different from that for T4 selection, as shown in Table 14:
The input clock is disqualified if any of the above conditions is not
satisfied.
In summary, the selected input clock can be switched by:
External Fast selection (supported by T0 path only);
Forced selection;
Revertive switch;
Non-Revertive switch (supported by T0 path only);
T4 DPLL locked to T0 DPLL output (supported by T4 path only).
3.8.2.1
Revertive Switch
In Revertive switch, the selected input clock is switched when
another qualified input clock with a higher priority than the current
selected input clock is available.
The selected input clock is switched if any of the following is satis-
fied:
the selected input clock is disqualified;
another qualified input clock with a higher priority than the
selected input clock is available.
A qualified input clock with the highest priority is selected by revertive
switch. If more than one qualified input clock is available and has the
same priority, the input clock with the smallest ‘n’ is selected. See
Table 9 for the ‘n’ assigned to each input clock.
Table 14: Conditions of Qualified Input Clocks Available for T0 & T4
Selection
Conditions of Qualified Input Clocks Available for T0 & T4 Selection
T0
Valid, i.e., the INn_CMOS 1 / INn_DIFF 1 bit is ‘1’;
Priority
enabled,
i.e.,
the
corresponding
INn_CMOS_SEL
_PRIORITY[3:0] / INn_DIFF_SEL_PRIORITY[3:0] bits are not ‘0000’
T4
Valid (all the validity conditions listed in Chapter 3.8.1 Input Clock Valid-
ity are satisfied);
Priority
enabled,
i.e.,
the
corresponding
INn_CMOS_SEL
_PRIORITY[3:0] / INn_DIFF_SEL_PRIORITY[3:0] bits are not ‘0000’
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/26SF11PA | CONN PLUG 11POS STRAIGHT W/PINS |
| VE-B2V-MW-F4 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-B2T-MW-F1 | CONVERTER MOD DC/DC 6.5V 100W |
| D38999/26MH21SA | CONN PLUG 21POS STRAIGHT W/SCKT |
| MS3450L18-9S | CONN RCPT 7POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82V3355TFG8 | 功能描述:IC PLL WAN SYNC ETH 64-TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| IDT82V3355TFGBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:SYNCHRONOUS ETHERNET WAN PLL |
| IDT82V3358 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:SYNCHRONOUS ETHERNET WAN PLL |
| IDT82V3358EDG | 功能描述:IC PLL WAN SYNC ETHERNET 64TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| IDT82V3358EDG8 | 制造商:Integrated Device Technology Inc 功能描述:IC PLL WAN SYNC ETHERNET 64TQFP |
發布緊急采購，3分鐘左右您將得到回復。