參數資料
型號： ISP1563BM,557
廠商： ST-ERICSSON
元件分類： 總線控制器
英文描述： UNIVERSAL SERIAL BUS CONTROLLER, PQFP100
封裝： 14 X 14 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-420-1, LQFP-100
文件頁數： 38/102頁
文件大?。?/td> 466K
代理商： ISP1563BM,557
ISP1563_2
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 02 — 15 March 2007
40 of 102
NXP Semiconductors
ISP1563
HS USB PCI Host Controller
11.1.4 HcInterruptStatus register
This is a 4-byte register that provides the status of the events that cause hardware
interrupts. The bit allocation of the register is given in Table 49. When an event occurs, the
Host Controller sets the corresponding bit in this register. When a bit becomes set, a
hardware interrupt is generated, if the interrupt is enabled in the HcInterruptEnable
register (see Table 51) and the MIE (Master Interrupt Enable) bit is set. The HCD may
clear specic bits in this register by writing logic 1 to the bit positions to be cleared. The
HCD may not set any of these bits. The Host Controller does not clear the bit.
Table 48.
HcCommandStatus - Host Controller Command Status register bit description
Address: Content of the base address register + 08h
Bit
Symbol
Description
31 to 18 reserved
-
17 to 16 SOC[1:0]
Scheduling Overrun Count: The bit is incremented on each scheduling overrun error. It is initialized
to 00b and wraps around at 11b. It must be incremented when a scheduling overrun is detected, even
if SO (bit 0 in HcInterruptStatus) is already set. This is used by the HCD to monitor any persistent
scheduling problems.
15 to 4
reserved
-
3
OCR
Ownership Change Request: This bit is set by an OS HCD to request a change of control of the Host
Controller. When set, the Host Controller must set OC (bit 30 in HcInterruptStatus). After the
changeover, this bit is cleared and remains so until the next request from the OS HCD.
2
BLF
Bulk List Filled: This bit is used to indicate whether there are any Transfer Descriptors (TDs) on the
bulk list. It is set by the HCD whenever it adds a TD to an ED in the bulk list. When the Host Controller
begins to process the head of the bulk list, it checks Bulk-Filled (BF). If BLF is logic 0, the Host
Controller does not need to process the bulk list. If BLF is logic 1, the Host Controller needs to start
processing the bulk list and set BF to logic 0. If the Host Controller nds a TD on the list, then the Host
Controller must set BLF to logic 1, causing the bulk list processing to continue. If no TD is found on the
bulk list, and if the HCD does not set BLF, then BLF is still logic 0 when the Host Controller completes
processing the bulk list and the bulk list processing stops.
1
CLF
Control List Filled: This bit is used to indicate whether there are any TDs on the control list. It is set
by the HCD whenever it adds a TD to an ED in the control list.
When the Host Controller begins to process the head of the control list, it checks CLF. If CLF is logic 0,
the Host Controller does not need to process the control list. If Control-Filled (CF) is logic 1, the Host
Controller needs to start processing the control list and set CLF to logic 0. If the Host Controller nds a
TD on the list, then the Host Controller must set CLF to logic 1, causing the control list processing to
continue. If no TD is found on the control list, and if the HCD does not set CLF, then CLF is still logic 0
when the Host Controller completes processing the control list and the control list processing stops.
0
HCR
Host Controller Reset: This bit is set by the HCD to initiate a software reset of the Host Controller.
Regardless of the functional state of the Host Controller, it moves to the USBSUSPEND state in which
most of the operational registers are reset, except those stated otherwise; for example, IR (bit 8) in the
HcControl register, and no host bus accesses are allowed. This bit is cleared by the Host Controller on
completing the reset operation. The reset operation must be completed within 10
s. This bit, when
set, must not cause a reset to the root hub and no subsequent reset signaling must be asserted to its
downstream ports.
Table 49.
HcInterruptStatus - Host Controller Interrupt Status register bit allocation
Address: Content of the base address register + 0Ch
Bit
31
30
29
28
27
26
25
24
Symbol
reserved[1]
OC
reserved[1]
Reset
00000000
Access
R/W
相關PDF資料
PDF描述
ISP1564ET,551 PCI BUS CONTROLLER, PBGA100
ISP1582BS,557 UNIVERSAL SERIAL BUS CONTROLLER, PQCC56
ISP1583ET1,118 UNIVERSAL SERIAL BUS CONTROLLER, PBGA64
ISP1583BS,551 UNIVERSAL SERIAL BUS CONTROLLER, PQCC64
ISP1583ET2 UNIVERSAL SERIAL BUS CONTROLLER, PBGA64
相關代理商/技術參數
參數描述
ISP1563BMGA 功能描述:IC USB HOST CTRL HI-SPD 128LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
ISP1563BMGE 功能描述:IC USB PCI HOST CTRLR 128-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
ISP1563BM-T 功能描述:USB 接口集成電路 USB 2.0 4PORT PCI HOST CONTROL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1563BMUM 功能描述:IC USB HOST CTRL HI-SPD 128LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
ISP1564 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Hi-Speed USB PCI host controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*