- 您現在的位置：買賣IC網 > PDF目錄17277 > KEYMATEK (Silicon Laboratories Inc)BOARD EVAL ITO FILM F800 PDF資料下載
參數資料
| 型號： | KEYMATEK |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 25/250頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL ITO FILM F800 |
| 標準包裝： | 1 |
| 系列： | QuickSense™ |
| 傳感器類型： | 觸摸，電容式 |
| 傳感范圍： | 13 個按鈕/鍵 |
| 接口： | USB |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板，線纜 |
| 已用 IC / 零件： | C8051F800 |
| 產品目錄頁面： | 626 (CN2011-ZH PDF) |
| 其它名稱： | 336-1818 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁
C8051F80x-83x
120
Rev. 1.0
20. Power Management Modes
The C8051F80x-83x devices have three software programmable power management modes: Idle, Stop,
and Suspend. Idle mode and Stop mode are part of the standard 8051 architecture, while Suspend mode
is an enhanced power-saving mode implemented by the high-speed oscillator peripheral.
Idle mode halts the CPU while leaving the peripherals and clocks active. In Stop mode, the CPU is halted,
all interrupts and timers (except the Missing Clock Detector) are inactive, and the internal oscillator is
stopped (analog peripherals remain in their selected states; the external oscillator is not affected). Sus-
pend mode is similar to Stop mode in that the internal oscillator and CPU are halted, but the device can
wake on events such as a Port Mismatch, Comparator low output, or a Timer 3 overflow. Since clocks are
running in Idle mode, power consumption is dependent upon the system clock frequency and the number
of peripherals left in active mode before entering Idle. Stop mode and Suspend mode consume the least
power because the majority of the device is shut down with no clocks active. SFR Definition 20.1 describes
the Power Control Register (PCON) used to control the C8051F80x-83x's Stop and Idle power manage-
ment modes. Suspend mode is controlled by the SUSPEND bit in the OSCICN register (SFR Definition
22.3).
Although the C8051F80x-83x has Idle, Stop, and Suspend modes available, more control over the device
power can be achieved by enabling/disabling individual peripherals as needed. Each analog peripheral
can be disabled when not in use and placed in low power mode. Digital peripherals, such as timers or
serial buses, draw little power when they are not in use. Turning off oscillators lowers power consumption
considerably, at the expense of reduced functionality.
20.1. Idle Mode
Setting the Idle Mode Select bit (PCON.0) causes the hardware to halt the CPU and enter Idle mode as
soon as the instruction that sets the bit completes execution. All internal registers and memory maintain
their original data. All analog and digital peripherals can remain active during Idle mode.
Idle mode is terminated when an enabled interrupt is asserted or a reset occurs. The assertion of an
enabled interrupt will cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU to resume
operation. The pending interrupt will be serviced and the next instruction to be executed after the return
from interrupt (RETI) will be the instruction immediately following the one that set the Idle Mode Select bit.
If Idle mode is terminated by an internal or external reset, the CIP-51 performs a normal reset sequence
and begins program execution at address 0x0000.
Note:
If the instruction following the write of the IDLE bit is a single-byte instruction and an interrupt occurs during the
execution phase of the instruction that sets the IDLE bit, the CPU may not wake from Idle mode when a future
interrupt occurs. Therefore, instructions that set the IDLE bit should be followed by an instruction that has two
or more opcode bytes, for example:
// in ‘C’:
PCON |= 0x01;
// set IDLE bit
PCON = PCON;
// ... followed by a 3-cycle dummy instruction
; in assembly:
ORL PCON, #01h
; set IDLE bit
MOV PCON, PCON
; ... followed by a 3-cycle dummy instruction
If enabled, the Watchdog Timer (WDT) will eventually cause an internal watchdog reset and thereby termi-
nate the Idle mode. This feature protects the system from an unintended permanent shutdown in the event
of an inadvertent write to the PCON register. If this behavior is not desired, the WDT may be disabled by
software prior to entering the Idle mode if the WDT was initially configured to allow this operation. This pro-
vides the opportunity for additional power savings, allowing the system to remain in the Idle mode indefi-
nitely, waiting for an external stimulus to wake up the system. Refer to Section “29.4. Watchdog Timer
Mode” on page 236 for more information on the use and configuration of the WDT.
相關PDF資料 |
PDF描述 |
|---|---|
| GEC22DRXI | CONN EDGECARD 44POS DIP .100 SLD |
| RN-0512S | CONV DC/DC 1.25W 05VIN 12VOUT |
| GBC15DRTS | CONN EDGECARD 30POS DIP .100 SLD |
| GCC08DREI | CONN EDGECARD 16POS .100 EYELET |
| GBC10DRAN | CONN EDGECARD 20POS R/A .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KEYPAD-HOA-BLK | 制造商:Eaton Corporation 功能描述:KEYPAD, HAND/OFF/AUTO |
| KEY-RING LED | 制造商:Energizer Battery Company 功能描述: |
| KEYRINGS | 制造商:KEY SECURE 功能描述:KEY RING PK10 制造商:KEY SECURE 功能描述:KEY RING, PK10 制造商:KEY SECURE 功能描述:KEY RING, PK10, SVHC:No SVHC (20-Jun-2013) |
| KEYS | 制造商:KEY SECURE 功能描述:SPARE KEYS FOR KEYSECURE RANGE |
| KEY-START-ALT | 制造商:TE Connectivity 功能描述:GEN-SET CONTROLLER KEY START OPTION |
發布緊急采購，3分鐘左右您將得到回復。