參數資料
型號： L6460TR
廠商： STMICROELECTRONICS
元件分類： 運動控制電子
英文描述： STEPPER MOTOR CONTROLLER, PQFP64
封裝： 10 X 10 MM, 1 MM HEIGHT, ROHS COMPLIANT, TQFP-64
文件頁數： 103/139頁
文件大?。?/td> 3837K
代理商： L6460TR
Power bridges
L6460
66/139
Doc ID 17713 Rev 1
The allowable control modes are as follows:
1.
Stepping sequence left to external microcontroller: in this mode the current level in
each motor winding is set by the microcontroller via the serial interface.
2.
Full step: in this mode the electrical angle will change by 90° steps at each StepReq
signal transition. There are two possibilities:
–
Normal step (two phases on): in normal step mode both windings are energized
simultaneously and the current will be alternately reversed. The resulting electrical
angles will be 45°, 135°, 225° and 315°.
–
Wave drive (one phase on): In wave drive mode each winding is alternately
energized and reversed. The resulting electrical angles will be 90°, 180° and 270°
and 360°.
3.
Half step: in this mode, one motor winding is energized and then two windings
alternately so the electrical angles the motor will do when rotating in clockwise direction
and using the same current limit in both the phases are: 45°, 90°, 135°, 180°, 225°,
270°, 315° and 360°.
4.
Microstepping: in this mode the current in each motor winding has a quasi sinusoidal
profile. The increment between each step is obtained at each transition of StepCmd bit
in StepCmd register. The difference between each step could be chosen (4, 8 or 16
levels for each phase) according to following table:
Note:
When in 1/16 step mode, the best phase approximation of sinusoidal wave, is obtained by
repeating the “F” step as follows: 0, 1, 2, 3, … , D, E, F, F, F, E, D, … , 3, 2, 1, 0
When internal stepping sequence generation is used, the stepping direction is set by the
StepDir bit according to the Table 23.
Table 21.
Sequencer driver
StepFromGpio
Sequencer driver
0
StepCmd bit in StepCmd register.
1
GPIO12 input pin.
Table 22.
Stepper driving mode
StepCtrlMode[2:0]
Control mode
Description
000 or 111
No Control
Stepping sequence control left to the external
controller
001
Half Step
Half step
010
Normal Step
Full step (two phases on)
011
Wave Drive
Full step (one phase on)
100
1/4 Step
Four micro steps
101
1/8 Step
Eight micro steps
110
1/16 Step
Sixteen micro steps
相關PDF資料
PDF描述
L6515 BRUSH DC MOTOR CONTROLLER, 0.01 A, PQCC44
L6560AD 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560AD013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560D013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6562ATN SWITCHING CONTROLLER, PDIP8
相關代理商/技術參數
參數描述
L6470 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:dSPIN fully integrated microstepping motor driver with motion engine and SPI
L64702QC-33 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
L64704 制造商:未知廠家 制造商全稱:未知廠家 功能描述:L64704 Satellite Decoder technical manual 5/97
L6470H 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A 1/128 Microstepping SPI RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L6470HTR 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A Bipolar dSPIN MicroStepping RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*