參數資料
型號: L6460TR
廠商: STMICROELECTRONICS
元件分類: 運動控制電子
英文描述: STEPPER MOTOR CONTROLLER, PQFP64
封裝: 10 X 10 MM, 1 MM HEIGHT, ROHS COMPLIANT, TQFP-64
文件頁數: 86/139頁
文件大?。?/td> 3837K
代理商: L6460TR
Main switching regulator
L6460
50/139
Doc ID 17713 Rev 1
12
Main switching regulator
Main switching regulator is an asynchronous switching regulator intended to be the source
of the main voltage in the system. It implements a soft start strategy and could be a system
regulator so even if its output voltage VSWmain is not used to power any internal circuit,
L6460 will check that it is in the good value range before enabling all its internal functions.
When L6460 detects a system regulator under-voltage event with a duration longer than the
period defined by the deglitch filter (tprim_uv), it will enter in reset state signaling this event to
the microcontroller by pulling low the nRESET pin and disabling most of its internal block
(e.g. bridges, GPIOs, …).
The output voltage will be externally set by a divider network connected to feedback pin. To
reduce as much as possible the regulation voltage error L6460 has the possibility to choose
between four feedback voltage references (and, as a consequence, four under-voltage
thresholds) using the serial interface. The feedback reference voltage selection is made by
writing the SelFBRef bits in the MainSwCfg register.
Here after are summarized the primary features of this regulator:
Internal power switch.
Soft start circuitry to limit inrush current flow from primary supply.
Internally generated PWM (250 kHz switching frequency).
Nonlinear pulse skipping control.
Protected against load short circuit.
Cycle by cycle current limiting using internal current sensor.
Under voltage signal (both continuous and latched) accessible through SPI.
When L6460 is in “l(fā)ow power mode”, this regulator will be disabled.
In order to save external components and power when using two or more L6460 IC’s on the
same board, the primary switching regulator can be disabled by serial interface. Care must
be paid using this function because an under-voltage on this regulator, as previously seen,
will be read as a fault condition by L6460.
12.1
Pulse skipping operation
Pulse skipping is a well known, non linear, control strategy used in switching regulators.
In this technique (see Figure 11) the feedback comparator output is sampled at the
beginning of each switching cycle. At this time, if the sampled value shows that output
voltage is lower than requested one, the complete PWM duty cycle is applied to power
switch; otherwise no PWM is applied and the switching cycle is skipped. Once PWM is
applied to power element only a current limit event can disable the power switch before the
whole duty cycle is finished.
相關PDF資料
PDF描述
L6515 BRUSH DC MOTOR CONTROLLER, 0.01 A, PQCC44
L6560AD 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560AD013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560D013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6562ATN SWITCHING CONTROLLER, PDIP8
相關代理商/技術參數
參數描述
L6470 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:dSPIN fully integrated microstepping motor driver with motion engine and SPI
L64702QC-33 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
L64704 制造商:未知廠家 制造商全稱:未知廠家 功能描述:L64704 Satellite Decoder technical manual 5/97
L6470H 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A 1/128 Microstepping SPI RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L6470HTR 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A Bipolar dSPIN MicroStepping RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube