參數資料
型號： L6460TR
廠商： STMICROELECTRONICS
元件分類： 運動控制電子
英文描述： STEPPER MOTOR CONTROLLER, PQFP64
封裝： 10 X 10 MM, 1 MM HEIGHT, ROHS COMPLIANT, TQFP-64
文件頁數： 34/139頁
文件大小： 3837K
代理商： L6460TR
L6460
Serial interface
Doc ID 17713 Rev 1
129/139
23
Serial interface
L6460 can communicate with an external microprocessor by using an integrated slave SPI
(serial protocol interface). Through this interface almost all L6460 functionalities can be
controlled and all the ICs can be seen as a register map made by 128 register of 16-bit
each.
The SPI is a simple industry standard communications interface commonly used in
embedded systems and it has the following four I/O pins:
–
MISO (master input slave output)
–
MOSI (master output slave input)
–
SCLK (serial clock [controlled by the master])
–
nSS (slave select active low [controlled by the master])
The “MISO” (master in, slave out) signal carries synchronous data from the slave to the
master device. The MOSI (master out, slave in) signal carries synchronous data from the
master to the slave device. The SCLK signal is driven by the master, synchronizing all data
transfers. Each SPI slave device has one nSS signal that is an active-low slave input/master
output pin. Slave devices do not respond to transactions unless their nSS input signal is
driven low. Master device interfacing with multiple SPI slave devices has an nSS signal for
each slave device.
L6460 will maintain its MISO pin in high impedance until it does not recognize its address in
serial frame.
23.1
Read transaction
A read transaction (see Figure 45) is always started by the master device that lowers the
nSS pin. The other bits are then sent on the MOSI pin with this order:
1.
7-bit representing the address of the register that must be read (MSB first [A6…A0]);
2.
2-bit that must be “10” for a read transaction;
3.
2-bit representing L6460 IC address;
4.
1-bit reserved for future use that must be set at “0”.
At this point the data stored in the register at the selected address will be shifted out on the
MISO pin.
The read operation is terminated by raising the signal on nSS pin.
相關PDF資料
PDF描述
L6515 BRUSH DC MOTOR CONTROLLER, 0.01 A, PQCC44
L6560AD 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560AD013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6560D013TR 0.7 A POWER FACTOR CONTROLLER, PDSO8
L6562ATN SWITCHING CONTROLLER, PDIP8
相關代理商/技術參數
參數描述
L6470 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:dSPIN fully integrated microstepping motor driver with motion engine and SPI
L64702QC-33 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
L64704 制造商:未知廠家 制造商全稱:未知廠家 功能描述:L64704 Satellite Decoder technical manual 5/97
L6470H 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A 1/128 Microstepping SPI RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L6470HTR 功能描述:馬達/運動/點火控制器和驅動器 8 - 45V 7.0A Bipolar dSPIN MicroStepping RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*