參數資料
型號： LAN83C185-JT
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 網絡接口
英文描述： HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER
中文描述： DATACOM, ETHERNET TRANSCEIVER, PQFP64
封裝： 10 X 10 MM, 1.40 MM HEIGHT, ROHS COMPLIANT, TQFP-64
文件頁數： 22/61頁
文件大小： 459K
代理商： LAN83C185-JT
High Performance Single Chip Low Power 10/100 Ethernet Physical Layer Transceiver (PHY)
Datasheet
Rev. 0.8 (11-16-04)
22
SMSC LAN83C185
DATASHEET
4.3.8
Receiver Errors
During a frame, unexpected code-groups are considered receive errors. Expected code groups are the
DATA set (0 through F), and the /T/R/ (ESD) symbol pair. When a receive error occurs, the RX_ER
signal is asserted and arbitrary data is driven onto the RXD[3:0] lines. Should an error be detected
during the time that the /J/K/ delimiter is being decoded (bad SSD error), RX_ER is asserted true and
the value ‘1110’ is driven onto the RXD[3:0] lines. Note that the Valid Data signal is not yet asserted
when the bad SSD error occurs.
4.3.9
100M Receive Data across the MII
The 4-bit data nibbles are sent to the MII block. These data nibbles are clocked to the controller at a
rate of 25MHz. The controller samples the data on the rising edge of RX_CLK. To ensure that the
setup and hold requirements are met, the nibbles are clocked out of the PHY on the falling edge of
RX_CLK. RX_CLK is the 25MHz output clock for the MII bus. It is recovered from the received data
to clock the RXD bus. If there is no received signal, it is derived from the system reference clock
(CLKIN).
When tracking the received data, RX_CLK has a maximum jitter of 0.8ns (provided that the jitter of the
input clock, CLKIN, is below 100ps).
4.4
10Base-T Transmit
Data to be transmitted comes from the MAC layer controller. The 10Base-T transmitter receives 4-bit
nibbles from the MII at a rate of 2.5MHz and converts them to a 10Mbps serial data stream. The data
stream is then Manchester-encoded and sent to the analog transmitter, which drives a signal onto the
twisted pair via the external magnetics.
The 10M transmitter uses the following blocks:
■
MII (digital)
■
TX 10M (digital)
■
10M Transmitter (analog)
■
10M PLL (analog)
4.4.1
10M Transmit Data across the MII
The MAC controller drives the transmit data onto the TXD BUS. When the controller has driven TX_EN
high to indicate valid data, the data is latched by the MII block on the rising edge of TX_CLK. The data
is in the form of 4-bit wide 2.5MHz data.
In order to comply with legacy 10Base-T MAC/Controllers, in Half-duplex mode the PHY loops back
the transmitted data, on the receive path. This does not confuse the MAC/Controller since the COL
signal is not asserted during this time. The PHY also supports the SQE (Heartbeat) signal. See
Section
5.4.2, "Collision Detect," on page 44
for more details.
4.4.2
Manchester Encoding
The 4-bit wide data is sent to the TX10M block. The nibbles are converted to a 10Mbps serial NRZI
data stream. The 10M PLL locks onto the external clock or internal oscillator and produces a 20MHz
clock. This is used to Manchester encode the NRZ data stream. When no data is being transmitted
(TX_EN is low, the TX10M block outputs Normal Link Pulses (NLPs) to maintain communications with
the remote link partner.
4.4.3
10M Transmit Drivers
The Manchester encoded data is sent to the analog transmitter where it is shaped and filtered before
being driven out as a differential signal across the TXP and TXN outputs.
相關PDF資料
PDF描述
LAN8700 【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR TM in a Small Footprint
LAN9115 HIGHLY EFFICIENT SINGLE - CHIP 10/100 NON PCI ETHERNET CONTROLLER
LAN9115-MD HIGHLY EFFICIENT SINGLE - CHIP 10/100 NON PCI ETHERNET CONTROLLER
LAN9115-MT HIGHLY EFFICIENT SINGLE - CHIP 10/100 NON PCI ETHERNET CONTROLLER
LAN9116 Highly Efficient Single-Chip 10/100 Non-PCI Ethernet Controller
相關代理商/技術參數
參數描述
LAN83C795QFP WAF 制造商:SMSC 功能描述:
LAN8700 制造商:SMSC 制造商全稱:SMSC 功能描述:【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR TM in a Small Footprint
LAN8700AEZG 制造商:SMSC 功能描述:
LAN8700-AEZG 功能描述:以太網 IC HIPERFRM ETHRNT PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN8700C-AEZG 功能描述:以太網 IC IC w/HP Auto-MDIX Embedded Ethernet RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*