- 您現在的位置：買賣IC網 > PDF目錄367558 > LH7A405 Microcontroller PDF資料下載
參數資料
| 型號： | LH7A405 |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 28/53頁 |
| 文件大小： | 396K |
| 代理商： | LH7A405 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
LH7A405
32-Bit System-on-Chip
28
Advance Data Sheet
The DMA features:
Two dedicated channels for M2M and external M2P/
P2M
Ten fully independent, programmable DMA control-
ler internal M2P/P2M channels (5 Tx and 5 Rx)
Channels assignable to one of a number of different
peripherals
Independent source and destination address regis-
ters. Source and destination can be programmed to
auto-increment or not auto-increment for M2M chan-
nels
Two buffer descriptors per M2P and M2M channel to
avoid potential data under/over-flow due to software
introduced latency. A buffer refers to the area in sys-
tem memory that is characterized by a buffer
descriptor, ie., a start address and the length of the
buffer in bytes
No AMBA wrapping bursts for DMA channels; only
incrementing bursts are supported
Buffer size independent of the peripheral’s packet
size for the internal M2P channels. Transfers can
automatically switch between buffers
Maskable interrupt generation
Internal arbitration between DMA channels, plus
support for an AHB bus arbiter
DMA data transfer sizes, byte, word and quad-word
data transfers are supported using a 16-byte data
bay. Maximum data transfer size per M2M channel
is programmable
Per-channel clock gating reducing power in chan-
nels that have not been enabled by software. See
the ‘Clock and State Controller’ section.
A set of control and status registers are available to
the system processor for setting up DMA operations
and monitoring their status. System interrupts are gen-
erated when any/all of the DMA channels wish to
inform the processor to update the buffer descriptor.
The DMA controller can service 10 out of 20 possible
peripherals using the ten DMA channels, each with its
own peripheral DMA bus capable of simultaneously
transferring data in both directions.
The SD/MMC, UART1/2/3, USB Device, and USB
Host peripherals can each use two DMA channels, one
for transmit and one for receive. The AAC peripheral
can use six DMA channels (three transmit and three
receive) to allow different sample frequency data
queues to be handled with low software overheads.
The DMA controller includes an M2M transfer fea-
ture allowing block moves of data from one memory
address space to another with minimum of program
effort and time. An M2M software trigger capability is
provided. The DMA controller can also fill a block of
memory with data from a single location.
The DMA controller’s M2M channels can also be
used in M2P/P2M mode. A set of external handshake
signals DREQ, DACK and TC/DEOT are provided for
each of two M2M channels.
DREQ (input) can be programmed edge or level
active, and active HIGH or LOW. The peripheral may
hold DREQ active for the duration of the block transfers
or may assert/deassert on each transfer.
DACK (output) can be programmed active HIGH or
LOW. DACK will assert and return to de-asserted with
each Read or Write, the timing coinciding with nOE or
nWE from the EBI.
TC/DEOT is a bidirectional signal with programma-
ble direction and active polarity. When configured as an
Output, the DMA will assert Terminal Count (TC) on the
final transfer to coincide with the DACK, typically when
the byte count has expired. When configured as an
Input, the peripheral must assert DEOT concurrent with
DREQ for the final transfer in the block.
Transfer is terminated when DEOT is asserted by
the external peripheral or when the byte count expires,
whichever occurs first. Status bits indicate if the actual
byte count is equal to the programmed limit, and if the
count was terminated by peripheral asserting DEOT.
Terminating the transfer causes a DMA interrupt on
that channel and rollover to the ’other’ buffer if so con-
figured.
For byte- or word-wide peripherals, the DMA is pro-
grammed to request byte- or word-wide AHB transfers
respectively. The DMA does not issue an AHB HREQ
for a transfer until it has DREQ is asserted after a
DACK for the previous transfer has been asserted for
the duration of the programmed wait states in the SMC
(and possibly DREQ is sampled in the cycle DACK is
deasserted).
USB Device
The features of the USB are:
Fully compliant to USB 1.1 specification
Provides a high-level interface that shields the firm-
ware from USB protocol details
Compatible with both OpenHCI and Intel UHCI
standards
Supports full-speed (12 Mbps) functions
Supports Suspend and Resume signalling.
相關PDF資料 |
PDF描述 |
|---|---|
| LH8001 | Microprocessor |
| LH8002 | Microprocessor |
| LH8010 | Peripheral IC |
| LH8030 | Telecommunication IC |
| LH8036 | Peripheral IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LH8000A-C | 制造商:Black Box Corporation 功能描述:DUAL SPEED 10/100 STACKABLE HUB CLIENT |
| LH8000A-C-W1 | 制造商:Black Box Corporation 功能描述:1 YEAR WARRANTY FOR LH8000A-C |
| LH8000A-C-W3 | 制造商:Black Box Corporation 功能描述:3 YEAR WARRANTY FOR LH8000A-C |
| LH8000A-M | 制造商:Black Box Corporation 功能描述:DUAL SPEED 10/100 STACKABLE HUB MASTER |
| LH8000A-M-SOL-W1 | 制造商:Black Box Corporation 功能描述:1 YEAR WARRANTY FOR LH8000A-M-SOL |
發布緊急采購，3分鐘左右您將得到回復。