- 您現在的位置：買賣IC網 > PDF目錄3764 > MAX3107EAG+T (Maxim Integrated Products)IC UART SPI/I2C 128 FIFO 24SSOP PDF資料下載
參數資料
| 型號： | MAX3107EAG+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 31/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART SPI/I2C 128 FIFO 24SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 特點： | 內部振蕩器 |
| 通道數： | 4，QUART |
| FIFO's： | 128 字節 |
| 規程： | RS232，RS485 |
| 電源電壓： | 2.35 V ~ 3.6 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 24-SSOP |
| 包裝： | 標準包裝 |
| 其它名稱： | MAX3107EAG+TDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
SPI/I2C UART with 128-Word FIFOs
Bits 7–4: SwFlow[3:0]
The SwFlow[3:0] bits configure auto software flow control and/or special character detection in combination with the
characters defined in the XON1, XON2, XOFF1 and/or XOFF2 registers. See Table 3.
FlowCtrl[5:4] select which of the XON1, XON2, XOFF1 or/and XOFF2 characters are used for special character detec-
tion and/or auto flow control. If auto receiver flow control is enabled through SwFlowEn and FlowCtrl[7:6], the XON and
XOFF characters that the MAX3107 receives are filtered out and are not put into the RxFIFO. Set the SwFlowEn bit to
0 and set MODE2[4] to 1 to only enable special character detection. Under these conditions, auto flow transmit flow
control is not active.
If both special character detection (MODE2[4]) and auto software flow control (FlowCtrl[3]) are to be enabled, XON1
and XOFF1 define the auto flow control characters, while XON2 and XOFF2 define the special character detection
characters.
Bit 3: SwFlowEn
The SwFlowEn bit enables auto software flow control. The characters used for auto software flow control are selected in
SwFlow[7:4]. If special character detection (MODE2[4] set to 1) is used in addition to auto software flow control, XON1
and XOFF1 are used for flow control, while XON2 and XOFF2 define the special characters.
Bit 2: GPIAddr
The GPIAddr bit, when set, enables that the four GPIO_ inputs are used in conjunction with XOFF2 for the definition of a
special character. This can be used, for example, for defining the address of a RS-485 slave device through hardware.
The GPIO_ inputs logic levels, which define the 4 LSBs of the special character, while the 4 MSBs are defined by the
XOFF2[7:4] bits. If GPIAddr is set, the contents of the XOFF2[3:0] bits are neglected. In this case, the XOFF2[3:0] bits,
when read, also do not reflect the logic on GPIO_.
Bit 1: AutoCTS
The AutoCTS bit enables auto CTS flow control by which the transmitter stops and starts sending data depending on
the logic state at the CTS input. See the Auto Hardware Flow Control section for a description of AutoCTS flow con-
trol. Logic changes at the CTS input result in an ISR[7]: CTSInt interrupt. The transmitter must be turned off by setting
MODE1[1] to 1 before AutoCTS is enabled.
Bit 0: AutoRTS
The AutoRTS bit enables auto RTS flow control by which the MAX3107 sets its RTS/CLKOUT output dependent on
the receive FIFO fill level. The FIFO thresholds at which RTS/CLKOUT changes state are set in FlowLvl. See the Auto
Hardware Flow Control section for more information.
FlowCtrl—Flow Control Register
ADDRESS:
0x13
MODE:
R/W
BIT
7
6
5
4
3
2
1
0
NAME
SwFlow3
SwFlow2
SwFlow1
SwFlow0
SwFlowEn
GPIAddr
AutoCTS
AutoRTS
RESET
0
Maxim Integrated
37
MAX3107
相關PDF資料 |
PDF描述 |
|---|---|
| SC28C94A1A,518 | IC UART QUAD W/FIFO 52-PLCC |
| SC16C754BIA68,518 | IC UART QUAD W/FIFO 68-PLCC |
| SC26C92C1N,602 | IC UART DUAL W/FIFO 40-DIP |
| SC28L91A1B,551 | IC UART SINGLE W/FIFO 44-PQFP |
| SC28L91A1B,528 | IC UART SINGLE W/FIFO 44PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3107ETG/V+ | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3107ETG/V+T | 功能描述:UART 接口集成電路 SPI/IC UART with 128-Word FIFOs and Internal Oscillator RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3107ETG+ | 功能描述:UART 接口集成電路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3107ETG+T | 功能描述:UART 接口集成電路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| MAX3107EVKIT+ | 功能描述:UART 接口集成電路 UART with integrated Oscillator RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。