參數資料
型號： MBM29LV200B-12
廠商： Fujitsu Limited
英文描述： CMOS 2M (256K×8/128K ×16) Bit Flash Memory(2M (256K×8/128K ×16)位 單5V 電源電壓閃速存儲器)
中文描述： 200萬的CMOS（256K × 8/128K × 16）位閃存（200萬（256K × 8/128K × 16）位單5V的電源電壓閃速存儲器）
文件頁數： 10/50頁
文件大?。?/td> 469K
代理商： MBM29LV200B-12
10
MBM29LV200T
-10/-12
/MBM29LV200B
-10/-12
I
FUNCTIONAL DESCRIPTION
Read Mode
The MBM29LV200T/200B have two control functions which must be satisfied in order to obtain data at the
outputs. CE is the power control and should be used for a device selection. OE is the output control and should
be used to gate data to the output pins if a device is selected.
Address access time (t
ACC
) is equal to the delay from stable addresses to valid output data. The chip enable
access time (t
CE
) is the delay from stable addresses and stable CE to valid data at the output pins. The output
enable access time is the delay from the falling edge of OE to valid data at the output pins. (Assuming the
addresses have been stable for at least t
ACC
- t
CE
time.)
Standby Mode
There are two ways to implement the standby mode on the MBM29LV200T/200B devices, one using both the
CE and RESET pins; the other via the RESET pin only.
When using both pins, a CMOS standby mode is achieved with CE and RESET inputs both held at V
CC
±
0.3 V.
Under this condition the current consumed is less than 5
μ
A. The device can be read with standard access time
(t
CE
) from either of these standby modes.
When using the RESET pin only, a CMOS standby mode is achieved with RESET input held at V
SS
±
0.3 V
(CE = “H” or “L”). Under this condition the current is consumed is less than 5
μ
A. Once the RESET pin is taken
high, the device requires 500 ns of wake up time before outputs are valid for read access.
In the standby mode the outputs are in the high impedance state, independent of the OE input.
Automatic Sleep Mode
There is a function called automatic sleep mode to restrain power consumption during read-out of
MBM29LV200T/200B data. This mode can be used effectively with an application requested low power
consumption such as handy terminals.
To activate this mode, MBM29LV200T/200B automatically switch themselves to low power mode when
MBM29LV200T/200B addresses remain stably during access time of 300 ns. It is not necessary to control CE,
WE, and OE on the mode. Under the mode, the current consumed is typically 1
μ
A (CMOS Level).
Since the data are latched during this mode, the data are read out continuously. If the addresses are changed,
the mode is canceled automatically and MBM29LV200T/200B read-out the data for changed addresses.
Output Disable
With the OE input at a logic high level (V
IH
), output from the devices are disabled. This will cause the output pins
to be in a high impedance state.
Autoselect
The autoselect mode allows the reading out of a binary code from the devices and will identify its manufacturer
and type. This mode is intended for use by programming equipment for the purpose of automatically matching
the devices to be programmed with its corresponding Programming Algorithm. This mode is functional over the
entire temperature range of the devices.
To activate this mode, the programming equipment must force V
ID
(11.5 V to 12.5 V) on address pin A
9
. Two
identifier bytes may then be sequenced from the devices outputs by toggling address A
0
from V
IL
to V
IH
. All
addresses are DON’T CARES except A
0
, A
1
, A
6
, and A
-1
.
(See Tables 4.1 and 4.2.)
The manufacturer and device codes may also be read via the command register, for instances when the
MBM29LV200T/200B are erased or programmed in a system without access to high voltage on the A
9
pin. The
command sequence is illustrated in Table 7. (Refer to Autoselect Command section.)
相關PDF資料
PDF描述
MBM29LV200B 2 M (256 K ×8/128 K ×16)Flash Memory((256 K ×8/128 K ×16) 單3V 電源電壓閃速存儲器)
MBM29LV200T 2 M (256 K ×8/128 K ×16)Flash Memory((256 K ×8/128 K ×16) 單3V 電源電壓閃速存儲器)
MBM29LV320BE Triacs - I<sub>GT</sub>: 10 mA; I<sub>T</sub> (R<sub>MS</sub>): 1 A; V<sub>DRM</sub>: 800 V
MBM29LV320BE10TR 32 M (4 M X 8/2 M X 16) BIT
MBM29LV320TE90 32 M (4 M X 8/2 M X 16) BIT
相關代理商/技術參數
參數描述
MBM29LV200BC 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K X 8/128K X 16) BIT
MBM29LV200BC-12 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K X 8/128K X 16) BIT
MBM29LV200BC-12PFTN 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K X 8/128K X 16) BIT
MBM29LV200BC-12PFTR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K X 8/128K X 16) BIT
MBM29LV200BC-70 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:2M (256K X 8/128K X 16) BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*