- 您現在的位置：買賣IC網 > PDF目錄69026 > MC68HC05E0FN (MOTOROLA INC) 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQCC68 PDF資料下載
參數資料
| 型號： | MC68HC05E0FN |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQCC68 |
| 封裝： | PLASTIC, LCC-68 |
| 文件頁數： | 72/96頁 |
| 文件大?。?/td> | 890K |
| 代理商： | MC68HC05E0FN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁當前第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
8
MOTOROLA
8-8
MC68HC05E0
SERIAL INTERFACE
BD1, BD0 — Baud Rate Select Bits (see Table 8-2).
PS1, PS0 — Port Select Bits
These bits should be 01 (binary) to select an I2C-bus function (see Table 8-1).
The I2C-bus Interface is controlled via the SI S Register ($0011).
BB — Bus Busy Bit
BB is a read-only bit which indicates if the I2C-bus is busy or idle. BB is set if a START condition
is seen on the data line. This implies that another I2C-bus master is using the bus, and that if the
MC68HC05E0 tries to start an I2C-bus sequence a data/clock collision will occur. BB is cleared
when the corresponding STOP condition, implying that the bus is again idle, is detected on the
bus. This ag generates no interrupt.
1 (set)
–
Busy
0 (clear) –
Idle
ACK — Acknowledge Bit
ACK is a read-only bit which goes high if an acknowledge signal is given by a peripheral (via the
9th clock bit) after the MC68HC05E0 has transmitted a byte of data to it. ACK is updated at the
end of each receive sequence.
1 (set)
–
Acknowledgement received from peripheral
0 (clear) –
Acknowledgement not received from peripheral
TFF/DOIT — Transmission Failure Flag/“Do it” Bit
Writing this bit high starts an I2C-bus transaction. Reading this bit at the end of an I2C-bus
transmit sequence shows the state of the TFF ag. If high, this indicates a mismatch between data
in the SI Data Register and the data sent on the serial data line. Writing a zero to this bit clears
and resets the Transmission Failure Flag circuitry.
Read
Write
1 (set)
–
Transmission error
Start Send or Receive
0 (clear) –
No transmission error
Clear and reset TFF
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
State
on reset
Serial interface S register
$0011
BB
ACK
TFF/
DOIT
IRQ/
ACK
NMA
SP
ST
R/WB 0000 0000
74
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05E5P | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP28 |
| MC68HC05E5DW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO28 |
| MC68HC05J1ACP | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP20 |
| MC68HSC05J1ADW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC05J1AP | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05E16 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16256 bytes of user ROM, 320bytes of EPROM and 352 bytes of RAM |
| MC68HC05E16/D | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16256 bytes of user ROM, 320bytes of EPROM and 352 bytes of RAM |
| MC68HC05E16B | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16256 bytes of user ROM, 320bytes of EPROM and 352 bytes of RAM |
| MC68HC05E16CB | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16256 bytes of user ROM, 320bytes of EPROM and 352 bytes of RAM |
| MC68HC05E16CFB | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16256 bytes of user ROM, 320bytes of EPROM and 352 bytes of RAM |
發布緊急采購，3分鐘左右您將得到回復。