- 您現在的位置：買賣IC網 > PDF目錄45220 > MC68HC05J5P (MOTOROLA INC) 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP20 PDF資料下載
參數資料
| 型號： | MC68HC05J5P |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP20 |
| 封裝： | PLASTIC, DIP-20 |
| 文件頁數： | 30/69頁 |
| 文件大小： | 394K |
| 代理商： | MC68HC05J5P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
GENERAL RELEASE SPECIFICATION
December 11, 1996
MOTOROLA
MODES OF OPERATION
MC68HC05J5
6-2
REV 1.1
6.3
SELF-CHECK MODE
The self-check mode provides an internal check to determine if the device is func-
tional.
6.4
LOW-POWER MODES
In each of its conguration modes the MC68HC05J5 is capable of running in one
of several low-power operational modes. The WAIT and STOP instructions provide
two modes that reduce the power required for the MCU by stopping various inter-
nal clocks and/or the on-chip oscillator. The STOP and WAIT instructions are not
normally used if the COP Watchdog Timer is enabled. A mask option is provided
to convert the STOP instruction to a HALT, which is a WAIT-like instruction that
does not halt the COP Watchdog Timer but has a recovery delay. The ow of the
STOP, HALT, and WAIT modes are shown in Figure 6-1.
6.4.1 STOP Instruction
The STOP instruction can result in one of two modes of operation depending on
the STOP mask option chosen. One option is for the STOP instruction to operate
like the STOP in normal MC68HC05 family members and place the device in the
STOP Mode. The other option is for the STOP instruction to behave like a WAIT
instruction (except that the restart time will involve a delay) and place the device in
the HALT Mode.
6.4.1.1
STOP Mode
Execution of the STOP instruction in this mode (as chosen by a mask option)
places the MCU in its lowest power consumption mode. In the STOP Mode the
internal oscillator is turned off, halting all internal processing, including the COP
Watchdog Timer.
When the CPU enters STOP Mode the interrupt ags (TOF and RTIF) and the
interrupt enable bits (TOFE and RTIE) in the TCSR are cleared by internal hard-
ware to remove any pending timer interrupt requests and to disable any further
timer interrupts. Execution of the STOP instruction automatically clears the I-bit in
the Condition Code Register and sets the IRQE enable bit in the IRQ Control/Sta-
tus Register so that the IRQ external interrupt is enabled. All other registers,
including the other bits in the TCSR, and memory remain unaltered. All input/out-
put lines remain unchanged.
The MCU can be brought out of the STOP Mode only by an IRQ external interrupt
or an externally generated RESET or an LVR reset. When exiting the STOP Mode
the internal oscillator will resume after a 4064 internal processor clock cycle oscil-
lator stabilization delay.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05J5DW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC05J5CJDW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO16 |
| MC68HC05JB4DW | 8-BIT, MROM, 3 MHz, MICROCONTROLLER, PDSO28 |
| MC68HC05JJ6DW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP20 |
| MC68HC05JJ6P | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05JJ6 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers |
| MC68HC05JJ6CDW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers |
| MC68HC05JJ6CDWE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers |
| MC68HC05JJ6CP | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers |
| MC68HC05JJ6CPE | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:General Release Specification Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。