參數資料
型號: MC68HLC705KJ1CP
廠商: FREESCALE SEMICONDUCTOR INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP16
封裝: PLASTIC, DIP-16
文件頁數: 17/108頁
文件大小: 719K
代理商: MC68HLC705KJ1CP
Introduction
MC68HC705KJ1 MC68HRC705KJ1 MC68HLC705KJ1 Data Sheet, Rev. 4.1
16
Freescale Semiconductor
1.4.1 VDD and VSS
VDD and VSS are the power supply and ground pins. The MCU operates from a single power supply.
Very fast signal transitions occur on the MCU pins, placing high, short-duration current demands on the
power supply. To prevent noise problems, take special care, as Figure 1-3 shows, by placing the bypass
capacitors as close as possible to the MCU. C2 is an optional bulk current bypass capacitor for use in
applications that require the port pins to source high current levels.
Figure 1-3. Bypassing Layout Recommendation
1.4.2 OSC1 and OSC2
The OSC1 and OSC2 pins are the connections for the on-chip oscillator. The oscillator can be driven by
any of the following:
1.
Standard crystal (See Figure 1-4 and Figure 1-5.)
2.
Ceramic resonator (See Figure 1-6 and Figure 1-7.)
3.
Resistor/capacitor (RC) oscillator (Refer to Appendix A MC68HRC705KJ1.)
4.
External clock signal as shown in (See Figure 1-8.)
5.
Low speed (32 kHz) crystal connections (Refer to Appendix B MC68HLC705KJ1.)
The frequency, fOSC, of the oscillator or external clock source is divided by two to produce the internal
operating frequency, fOP.
1.4.2.1 Crystal Oscillator
Figure 1-4 and Figure 1-5 show a typical crystal oscillator circuit for an AT-cut, parallel resonant crystal.
Follow the crystal supplier’s recommendations, as the crystal parameters determine the external
component values required to provide reliable startup and maximum stability. The load capacitance
values used in the oscillator circuit design should include all stray layout capacitances.
To minimize output distortion, mount the crystal and capacitors as close as possible to the pins. An
internal startup resistor of approximately 2 M
is provided between OSC1 and OSC2 for the crystal
oscillator as a programmable mask option.
NOTE
Use an AT-cut crystal and not an AT-strip crystal because the MCU can
overdrive an AT-strip crystal.
C1
C2
MCU
C1
0.1
F
C2
V+
+
VDD
VSS
VDD
VSS
相關PDF資料
PDF描述
MC68HRC705KJ1CP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP16
MC68HC705L1B 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP56
MC68HC05L1FU 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PQFP64
MC68HC05L1B 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56
MC68HC705L2B 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP42
相關代理商/技術參數
參數描述
MC68HLC908JK3CP 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HLC908QT1CFQ 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HLC908QT4CDW 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HLC908QT4CFQ 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68HLC908QY1CDW 制造商:Rochester Electronics LLC 功能描述:LOW V-1.5K FLASH W/O ADC - Bulk