- 您現在的位置：買賣IC網 > PDF目錄359155 > MCZ33927EK (飛思卡爾半導體(中國)有限公司) Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod PDF資料下載
參數資料
| 型號： | MCZ33927EK |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Transistor; Type: Amplifiers/Bipolar; VCEO (V): -100; Ic (A): -1; Pc (W): 0.9; hFE: 140 to 350; VCE (sat) (V) max: -0.5; Package: TO-92Mod |
| 中文描述： | 三相場效應晶體管預驅動器 |
| 文件頁數： | 31/44頁 |
| 文件大?。?/td> | 490K |
| 代理商： | MCZ33927EK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
31
33927
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
MODE COMMAND
This command is sent by sending binary 010x xxxx data.
Table 11. Setting Interrupt Masks
Mask:bit
Description
MASK0:0
Overtemperature
on any gate drive output generates an interrupt if this bit is set.
MASK0:1
Desaturation
event on any output generates an interrupt if this bit is set.
MASK0:2
VLS undervoltage
generates an interrupt if this bit is set.
MASK0:3
Overcurrent Error
–if the overcurrent comparator threshold is exceeded, an interrupt is generated.
MASK1:0
Phase Error
–if any Phase comparator output is not at the expected value when an output is command on, an interrupt is
generated. This signal is the XOR of the phase comparator output with the output drive state, and blacked for the duration
of the desaturation blanking interval.
In FULLON mode, this signal is blanked and cannot generate an error.
MASK1:1
Framing Error
–if a framing error occurs, an interrupt is generated.
MASK1:2
Write Error
after locking.
MASK1:3
Reset Event
–If the IC is set or disabled, an interrupt occurs. Since the IC will always start from a reset condition, this can be
used to test the interrupt mechanism because when the IC comes out of RESET, an interrupt will immediately occur.
Table 12. MODE Command
SPI Data Bits
7
6
5
4
3
2
1
0
Write
0
1
0
0
Desaturation
Fault Mode
0
FULLON
Mode
Mode
Lock
Reset
0
0
0
0
Bit 0
–
Mode Lock
is used to enable or disable Mode Lock. If Bit 0 is set, changes to the internal registers are disallowed
to prevent inadvertent changes. This bit cannot be cleared once set. Since the mode Lock mode can only be set, this bit
prevents any subsequent, and likely erroneous, mode, deadtime, or mask register changes from being received. The only
way to clear this bit is to RESET the IC. If an attempt is made to write to a register when Mode Lock is enabled, a Write
Error fault is generated.
Bit 1
–
FULLON Mode.
If this bit is set, programmed deadtime control is disabled, making it is possible to have both high-
and low-side drivers in a phase on simultaneously. This could be useful in special applications such as alternator
regulators, or switched-reluctance motor drive applications. There is no deadtime control in FULLON mode. Input signals
directly control the output stages, synchronized with the internal clock.
This bit is a “0”, after RESET. Until overwritten, the IC operates normally; deadtime control and logic prevents both outputs
from being turned on simultaneously.
Bit 3
–
Desaturation Fault Mode
controls what happen when a desaturation event is detected. When set to “0”, any
desaturation on any channel causes all six output drivers to shutoff. The drivers can only be re-enabled by executing the
CLINT command. When 1, desaturation faults are completely ignored.
Bit 3 controls behavior if a Desaturation, or Phase Error event is detected. The possibilities are:
— 0: Default: When a Desaturation, or Phase Error event is detected on
any
channel,
all
channels turn off and generates
an Interrupt, if interrupts are enabled.
— 1: Disable: Desaturation /Phase Error channel shutdown is disabled, but interrupts are still possible if unmasked.
Sending a MODE command and setting the Mode Lock simultaneously are allowed. This sets the requested mode and locks out any further
changes.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33970EG | Dual Gauge Driver Integrated Circuit with Improved Damping Algorithms |
| MCZ33976EG | Dual Gauge Driver with Configurable esponse Time |
| MCZ33977EG | Single Gauge Driver |
| MCZ33989EG | System Basis Chip with High-Speed CAN Transceiver |
| MCZ33990EF | Enhanced Class B Serial Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33927EK/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver |
| MCZ33927EKR2 | 功能描述:功率驅動器IC THREE PHASE PRE- DRIVER RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MCZ33927R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver |
| MCZ33937AEK | 功能描述:馬達/運動/點火控制器和驅動器 3 Phase Pre-Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33937AEK/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Three Phase Field Effect Transistor Pre-driver |
發布緊急采購，3分鐘左右您將得到回復。