- 您現在的位置：買賣IC網 > PDF目錄359189 > MPC92433 (飛思卡爾半導體(中國)有限公司) 1428 MHz Dual Output LVPECL Clock Synthesizer PDF資料下載
參數資料
| 型號： | MPC92433 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 1428 MHz Dual Output LVPECL Clock Synthesizer |
| 中文描述： | 1428兆赫雙輸出的LVPECL時鐘合成器 |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 412K |
| 代理商： | MPC92433 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁
Advanced Clock Drivers Devices
Freescale Semiconductor
16
MPC92433
V
CC_PLL
Filter
The MPC92433 is a mixed analog/digital product. Its
analog circuitry is naturally susceptible to random noise,
especially if this noise is seen on the power supply pins.
Random noise on the V
CC_PLL
pin impacts the device AC
characteristics. The MPC92433 provides separate power
supplies for the digital circuitry (V
CC
) and the internal PLL
(V
CC_PLL
) of the device. The purpose of this design
technique is to isolate the high switching noise digital outputs
from the relatively sensitive internal analog phase-locked
loop. In digital system environments where it is more difficult
to minimize noise on the power supplies a second level of
isolation is recommended: a power supply filter on the
V
CC_PLL
pin for the MPC92433.
Figure 7. V
CC_PLL
Power Supply Filter
Figure 7
illustrates a recommended power supply filter
scheme.
The MPC92433 is most susceptible to noise with spectral
content in the 100 kHz to 1 MHz range. Therefore, the filter
should be designed to target this range. The key parameter
that needs to be met in the final filter design is the DC voltage
drop that will be seen between the V
CC
supply and the
V
CC_PLL
pin of the MPC92433. From the data sheet, the
V
CC_PLL
current (the current sourced through the V
CC_PLL
pin) is maximum 10 mA, assuming that a minimum of 2.985 V
must be maintained on the V
CC_PLL
pin. The resistor shown
in
Figure 7
must have a resistance of 10
–
15
to meet the
voltage drop criteria. The minimum values for R
F
and the filter
capacitor C
F
are defined by the filter characteristics: the RC
filter should provide an attenuation greater than 40 dB for
noise whose spectral content is above 100 kHz. In the
recommended filter shown in
Figure 7
the filter cut-off
frequency is around 3.0
–
4.5 kHz and the noise attenuation at
100 kHz is better than 42 dB.
As the noise frequency crosses the series resonant point
of an individual capacitor its overall impedance begins to look
inductive and thus increases with increasing frequency. The
parallel capacitor combination shown ensures that a low
impedance path to ground exists for frequencies well above
the bandwidth of the PLL.
The On-Chip Crystal Oscillator
The MPC92433 features an integrated on-chip crystal
oscillator to minimize system implementation cost. The
integrated oscillator is a Pierce-type that uses the crystal in
its parallel resonance mode. It is recommended to use a 15
to 20 MHz crystal with a load specification of C
L
= 10 pF.
Crystals with a load specification of C
L
= 20 pF may be used
at the expense of an resulting slightly higher frequency than
specified for the crystal. Externally connected capacitors on
both the XTAL_IN and XTAL_OUT pins are not required but
can be used to fine-tune the crystal frequency as desired.
The crystal, the trace and optional capacitors should be
placed on the board as close as possible to the MPC92433
XTAL_IN and XTAL_OUT pins to reduce crosstalk of active
signals into the oscillator. Short and wide traces further
reduce parasitic inductance and resistance. It is further
recommended to guard the crystal circuit by placing a ground
ring around the traces and oscillator components.
R
F
= 10–15
V
CC
C
F
= 22
μ
F
10 nF
33...100 nF
V
CC_PLL
V
CC
MPC92433
7
Table 22. Recommended Crystal Specifications
Parameter
Value
Crystal Cut
Fundamental AT Cut
Resonance Mode
Parallel
Crystal Frequency
16
–
20 MHz
Shunt Capacitance C
0
5
–
7 pF
Load Capacitance C
L
10 pF
相關PDF資料 |
PDF描述 |
|---|---|
| MPC953 | Low Voltage PLL Clock Driver(低壓PLL時鐘驅動器) |
| MPC9817 | Clock Generator for PowerQUICC and PowerPC Microprocessors and Microcontrollers |
| MPD1 | Peripheral IC |
| RPD1 | Peripheral IC |
| LPD1 | Peripheral IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC92433AE | 功能描述:時鐘合成器/抖動清除器 FSL 1428MHz Dual Out put LVPECL Clock Syn RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC92433AER2 | 功能描述:時鐘合成器/抖動清除器 FSL 1428MHz Dual Out put LVPECL Clock Syn RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC92439 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:900MHz, Low Voltage, LVPECL Clock Syntheesizer |
| MPC92439AC | 功能描述:IC SYNTHESIZER LVPECL 32-LQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| MPC92439ACR2 | 功能描述:IC SYNTHESIZER LVPECL 32-LQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
發布緊急采購，3分鐘左右您將得到回復。