![](http://datasheet.mmic.net.cn/180000/MT46V32M81AZ4-6T-G_datasheet_11334049/MT46V32M81AZ4-6T-G_42.png)
128Mb: x4, x8, x16
DDR SDRAM
09005aef8074a655
Micron Technology, Inc., reserves the right to change products or specifications without notice.
128MBDDRx4x8x16_2.fm - Rev. J 7/04 EN
42
2000 Micron Technology, Inc. All rights reserved.
NOTE:
tXSNR has been met (if the
previous state was self refresh).
2. This table is bank-specific, except where noted (i.e., the current state is for a specific bank and the commands shown are
those allowed to be issued to that bank when in that state). Exceptions are covered in the notes below.
3. Current state definitions:
Idle:The bank has been precharged, and tRP has been met.
Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no regis-
ter accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been termi-
nated.
Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been ter-
minated.
4. The following states must not be interrupted by a command issued to the same bank. DESELECT or NOP commands, or
allowable commands to the other bank should be issued on any clock edge occurring during these states. Allowable
Precharging:
Starts with registration of a PRECHARGE command and ends when tRP is met. Once tRP is
met, the bank will be in the idle state.
Row Activating:
Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is
met, the bank will be in the “row active” state.
Read w/Auto-
Precharge Enabled: Starts with registration of a READ command with auto precharge enabled and ends when
tRP has been met. Once tRP is met, the bank will be in the idle state.
Write w/Auto-
Precharge Enabled: Starts with registration of a WRITE command with auto precharge enabled and ends when
tRP has been met. Once tRP is met, the bank will be in the idle state.
5. The following states must not be interrupted by any executable command; DESELECT or NOP commands must be
applied on each positive clock edge during these states.
Table 9:
Truth Table – Current State Bank n - Command to Bank n
(Notes: 1-6; notes appear below and on next page)
CURRENT
STATE
CS#
RAS# CAS#
WE#
COMMAND/ACTION
NOTES
Any
HX
X
DESELECT (NOP/continue previous operation)
LH
H
NO OPERATION (NOP/continue previous operation)
Idle
LL
H
ACTIVE (select and activate row)
LL
L
H
AUTO REFRESH
7
LL
L
LOAD MODE REGISTER
7
Row
Active
LH
L
H
READ (select column and start READ burst)
10
LH
L
WRITE (select column and start WRITE burst)
10
LL
H
L
PRECHARGE (deactivate row in bank or banks)
8
Read
(Auto-
Precharge
Disabled)
LH
L
H
READ (select column and start new READ burst)
10
LH
L
WRITE (select column and start WRITE burst)
10, 12
LL
H
L
PRECHARGE (truncate READ burst, start PRECHARGE)
8
LH
H
L
BURST TERMINATE
9
Write
(Auto-
Precharge
Disabled)
LH
L
H
READ (select column and start READ burst)
10, 11
LH
L
WRITE (select column and start new WRITE burst)
10
LL
H
L
PRECHARGE (truncate WRITE burst, start PRECHARGE)
8, 11