![](http://datasheet.mmic.net.cn/180000/MT46V32M81AZ4-6T-G_datasheet_11334049/MT46V32M81AZ4-6T-G_9.png)
128Mb: x4, x8, x16
DDR SDRAM
09005aef8074a655
Micron Technology, Inc., reserves the right to change products or specifications without notice.
128MBDDRx4x8x16_2.fm - Rev. J 7/04 EN
9
2000 Micron Technology, Inc. All rights reserved.
Table 2:
Ball/Pin Descriptions
FBGA
NUMBERS
TSOP
NUMBERS
SYMBOL
TYPE
DESCRIPTION
G2, G3
45, 46
CK, CK#
Input
Clock: CK and CK# are differential clock inputs. All address and
control input signals are sampled on the crossing of the positive
edge of CK and negative edge of CK#. Output data (DQ and DQS)
is referenced to the crossings of CK and CK#.
H3
44
CKE
Input
Clock Enable: CKE HIGH activates and CKE LOW deactivates the
internal clock, input buffers and output drivers. Taking CKE LOW
provides PRECHARGE POWER-DOWN and SELF REFRESH
operations (all banks idle), or ACTIVE POWER-DOWN (row ACTIVE
in any bank). CKE is synchronous for POWER-DOWN entry and
exit, and for SELF REFRESH entry. CKE is asynchronous for SELF
REFRESH exit and for disabling the outputs. CKE must be
maintained HIGH throughout read and write accesses. Input
buffers (excluding CK, CK# and CKE) are disabled during POWER-
DOWN. Input buffers (excluding CKE) are disabled during SELF
REFRESH. CKE is an SSTL_2 input but will detect an LVCMOS
LOW
level after VDD is applied and until CKE is first brought HIGH,
after which it becomes a SSTL_2 input only.
H8
24
CS#
Input
Chip Select: CS# enables (registered LOW) and disables (registered
HIGH) the command decoder. All commands are masked when
CS# is registered HIGH. CS# provides for external bank selection
on systems with multiple banks. CS# is considered part of the
command code.
H7, G8,
G7
23, 22,
21
RAS#, CAS#,
WE#
Input
Command Inputs: RAS#, CAS#, and WE# (along with CS#) define
the command being entered.
3F
47
DM
Input
Input Data Mask: DM is an input mask signal for write data. Input
data is masked when DM is sampled HIGH along with that input
data during a WRITE access. DM is sampled on both edges of DQS.
Although DM pins are input-only, the DM loading is designed to
match that of DQ and DQS pins. For the x16, LDM is DM for DQ0–
DQ7 and UDM is DM for DQ8–DQ15. Pin 20 is a NC on x4 and x8.
20, 47
LDM, UDM
J8, J7
26, 27
BA0, BA1
Input
Bank Address Inputs: BA0 and BA1 define to which bank an
ACTIVE, READ, WRITE, or PRECHARGE command is being applied.
K7, L8, L7,
M8, M2, L3,
L2, K3, K2,
J3, K8,
J2
29, 30, 31,
32, 35, 36,
37, 38, 39,
40, 28
41
A0, A1, A2,
A3, A4, A5,
A6, A7, A8,
A9, A10,
A11
Input
Address Inputs: Provide the row address for ACTIVE commands,
and the column address and auto precharge bit (A10) for READ/
WRITE commands, to select one location out of the memory array
in the respective bank. A10 sampled during a PRECHARGE
command determines whether the PRECHARGE applies to one
bank (A10 LOW, bank selected by BA0, BA1) or all banks (A10
HIGH). The address inputs also provide the op-code during a
MODE REGISTER SET command. BA0 and BA1 define which mode
register (mode register or extended mode register) is loaded
during the LOAD MODE REGISTER command.